The ROHM BD72720 has 6 pins which may be configured as GPIOs. The
GPIO1 ... GPIO5 and EPDEN pins. The configuration is done to OTP at the
manufacturing, and it can't be read at runtime. The device-tree is
required to tell the software which of the pins are used as GPIOs.
Keep the pin mapping static regardless the OTP. This way the user-space
can always access the BASE+N for GPIO(N+1) (N = 0 to 4), and BASE + 5
for the EPDEN pin. Do this by setting always the number of GPIOs to 6,
and by using the valid-mask to invalidate the pins which aren't configured
as GPIOs.
First two pins can be set to be either input or output by OTP. Direction
can't be changed by software. Rest of the pins can be set as outputs
only. All of the pins support generating interrupts.
Support the Input/Output state getting/setting and the output mode
configuration (open-drain/push-pull).
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://patch.msgid.link/22e095ca92f0677ca3d3a768ad749629fc3c2006.1765804226.git.mazziesaccount@gmail.com
Signed-off-by: Lee Jones <lee@kernel.org>
Add a new driver which provides a 1-to-many mapping for a single real
GPIO using a multiplexer. Each virtual GPIO corresponds to a multiplexer
state which, if set for the multiplexer, connects the real GPIO to the
corresponding virtual GPIO.
This can help in various usecases. One practical case is the special
hardware design of the Realtek-based XS1930-10 switch from Zyxel. It
features two SFP+ ports/cages whose signals are wired directly to the
switch SoC. Although Realtek SoCs are short on GPIOs, there are usually
enough the fit the SFP signals without any hacks.
However, Zyxel did some weird design and connected RX_LOS, MOD_ABS and
TX_FAULT of one SFP cage onto a single GPIO line controlled by a
multiplexer (the same for the other SFP cage). The single multiplexer
controls the lines for both SFP and depending on the state, the
designated 'signal GPIO lines' are connected to one of the three SFP
signals.
Because the SFP core/driver doesn't support multiplexer but needs single
GPIOs for each of the signals, this driver fills the gap between both.
It registers a gpio_chip, provides multiple virtual GPIOs and sets the
backing multiplexer accordingly.
Due to several practical issues, this is input-only and doesn't support
IRQs.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Reviewed-by: Thomas Richard <thomas.richard@bootlin.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20251227180134.1262138-3-jelonek.jonas@gmail.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Selecting OF_GPIO is generally not allowed, it always gets enabled
when both GPIOLIB and OF are turned on.
The tb10x driver now warns about this after it was enabled for
compile-testing:
WARNING: unmet direct dependencies detected for OF_GPIO
Depends on [n]: GPIOLIB [=y] && OF [=n] && HAS_IOMEM [=y]
Selected by [y]:
- GPIO_TB10X [=y] && GPIOLIB [=y] && HAS_IOMEM [=y] && (ARC_PLAT_TB10X || COMPILE_TEST [=y])
OF_GPIO is not required for compile-testing and is already enabled
when the driver is usable, so just drop the 'select' line.
Fixes: 682fbb18e1 ("gpio: tb10x: allow building the module with COMPILE_TEST=y")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20251205095429.1291866-1-arnd@kernel.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
The regmap drivers need to be selected by each user, without that there
can be configurations that fail to link:
x86_64-linux-ld: drivers/gpio/gpio-qixis-fpga.o: in function `qixis_cpld_gpio_probe':
gpio-qixis-fpga.c:(.text+0x13a): undefined reference to `__devm_regmap_init_mmio_clk'
Fixes: e88500247d ("gpio: add QIXIS FPGA GPIO controller")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20251204094928.1031494-1-arnd@kernel.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Since PCI device should not be abusing platform device, MFD parent to
platform child path is no longer being pursued for this driver. Convert
it to auxiliary driver, which will be used by EHL PSE auxiliary device.
Signed-off-by: Raag Jadav <raag.jadav@intel.com>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20251112034040.457801-3-raag.jadav@intel.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Add better support for GPIOs shared by multiple consumers.
-----BEGIN PGP SIGNATURE-----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=fa8j
-----END PGP SIGNATURE-----
Merge tag 'gpio/shared-gpios-for-v6.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux.git into gpio/for-next
Immutable branch between the GPIO, ASoC and regulator trees for v6.19-rc1
Add better support for GPIOs shared by multiple consumers.
Add a virtual GPIO proxy driver which arbitrates access to a single
shared GPIO by multiple users. It works together with the core shared
GPIO support from GPIOLIB and functions by acquiring a reference to a
shared GPIO descriptor exposed by gpiolib-shared and making sure that
the state of the GPIO stays consistent.
In general: if there's only one user at the moment: allow it to do
anything as if this was a normal GPIO (in essence: just propagate calls
to the underlying real hardware driver). If there are more users: don't
allow to change the direction set by the initial user, allow to change
configuration options but warn about possible conflicts and finally:
treat the output-high value as a reference counted, logical "GPIO
enabled" setting, meaning: the GPIO value is set to high when the first
user requests it to be high and back to low once the last user stops
"voting" for high.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20251112-gpio-shared-v4-4-b51f97b1abd8@linaro.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
This module scans the device tree (for now only OF nodes are supported
but care is taken to make other fwnode implementations easy to
integrate) and determines which GPIO lines are shared by multiple users.
It stores that information in memory. When the GPIO chip exposing shared
lines is registered, the shared GPIO descriptors it exposes are marked
as shared and virtual "proxy" devices that mediate access to the shared
lines are created. When a consumer of a shared GPIO looks it up, its
fwnode lookup is redirected to a just-in-time machine lookup that points
to this proxy device.
This code can be compiled out on platforms which don't use shared GPIOs.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20251112-gpio-shared-v4-3-b51f97b1abd8@linaro.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Last user of linux/gpio/legacy-of-mm-gpiochip.h is gone.
Remove linux/gpio/legacy-of-mm-gpiochip.h and
CONFIG_OF_GPIO_MM_GPIOCHIP
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Remove legacy-of-mm-gpiochip.h header file. The above mentioned
file provides an OF API that's deprecated. There is no agnostic
alternatives to it and we have to open code the logic which was
hidden behind of_mm_gpiochip_add_data(). Note, most of the GPIO
drivers are using their own labeling schemas and resource retrieval
that only a few may gain of the code deduplication, so whenever
alternative is appear we can move drivers again to use that one.
[Text copied from commit 34064c8267 ("powerpc/8xx: Drop
legacy-of-mm-gpiochip.h header")]
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Add support for the GPIO controller found on some QIXIS FPGAs in
Layerscape boards such as LX2160ARDB and LS1046AQDS. This driver is
using gpio-regmap.
A GPIO controller has a maximum of 8 lines (all found in the same
register). Even within the same controller, the GPIO lines' direction is
fixed, which mean that both input and output lines are found in the same
register. This is why the driver also passed to gpio-regmap the newly
added .fixed_direction_output bitmap to represent the true direction of
the lines.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Michael Walle <mwalle@kernel.org> # for the gpio-regmap part
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Here is the big set of USB and thunderbolt drivers for 6.18-rc1. It was
another normal development cycle, with lots of the usual drivers getting
updates:
- Thunderbolt driver cleanups and additions
- dwc3 driver updates
- dwc2 driver updates
- typec driver updates
- xhci driver updates and additions
- offload USB engine updates for better power management
- unused tracepoint removals
- usb gadget fixes and updates as more users start to rely on these
drivers instead of the "old" function gadget drivers
- new USB device ids
- other minor driver USB driver updates
- new USB I/O driver framework and driver additions
The last item, the usb i/o driver, has an i2c and gpio driver added
through this tree. Those drivers were acked by the respective subsystem
maintainers, but you will get a merge conflict with the i2c tree where
new drivers were added in the same places in a Kconfig and Makefile.
The merge conflict is simple, just take both sides.
All of these have been in linux-next for a while, with the only issue
being the i2c tree merge conflicts.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCaOEo8Q8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynpOQCgkenJzjsGVHhl/tm447z3pQ8NtvQAn2GfxMF9
4jQlUtr6McyzCLVPOZRD
=pPei
-----END PGP SIGNATURE-----
Merge tag 'usb-6.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt updates from Greg KH:
"Here is the big set of USB and thunderbolt drivers for 6.18-rc1. It
was another normal development cycle, with lots of the usual drivers
getting updates:
- Thunderbolt driver cleanups and additions
- dwc3 driver updates
- dwc2 driver updates
- typec driver updates
- xhci driver updates and additions
- offload USB engine updates for better power management
- unused tracepoint removals
- usb gadget fixes and updates as more users start to rely on these
drivers instead of the "old" function gadget drivers
- new USB device ids
- other minor driver USB driver updates
- new USB I/O driver framework and driver additions"
The last item, the usb i/o driver, has an i2c and gpio driver added
through this tree. Those drivers were acked by the respective
subsystem maintainers.
All of these have been in linux-next for a while"
* tag 'usb-6.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (132 commits)
usb: vhci-hcd: Prevent suspending virtually attached devices
USB: serial: option: add SIMCom 8230C compositions
thunderbolt: Fix use-after-free in tb_dp_dprx_work
usb: xhci: align PORTSC trace with one-based port numbering
usb: xhci: correct indentation for PORTSC tracing function
usb: xhci: improve TR Dequeue Pointer mask
usb: xhci-pci: add support for hosts with zero USB3 ports
usb: xhci: Update a comment about Stop Endpoint retries
Revert "usb: xhci: Avoid Stop Endpoint retry loop if the endpoint seems Running"
usb: gadget: f_rndis: Refactor bind path to use __free()
usb: gadget: f_ecm: Refactor bind path to use __free()
usb: gadget: f_acm: Refactor bind path to use __free()
usb: gadget: f_ncm: Refactor bind path to use __free()
usb: gadget: Introduce free_usb_request helper
usb: gadget: Store endpoint pointer in usb_request
usb: host: xhci-rcar: Add Renesas RZ/G3E USB3 Host driver support
usb: host: xhci-plat: Add .post_resume_quirk for struct xhci_plat_priv
usb: host: xhci-rcar: Move R-Car reg definitions
dt-bindings: usb: Document Renesas RZ/G3E USB3HOST
usb: gadget: f_fs: Fix epfile null pointer access after ep enable.
...
GPIO core:
- add support for sparse pin ranges to the glue between GPIO and pinctrl
- use a common prefix across all GPIO descriptor flags for improved
namespacing
New drivers:
- add new GPIO driver for the Nuvoton NCT6694
- add new GPIO driver for MAX7360
Driver improvements:
- add support for Tegra 256 to the gpio-tegra186 driver
- add support for Loongson-2K0300 to the gpio-loongson-64bit driver
- refactor the gpio-aggregator module to expose its GPIO forwarder API
to other in-kernel users (to enable merging of a new pinctrl driver
that uses it)
- convert all remaining drivers to using the modernized generic GPIO chip
API and remove the old interface
- stop displaying global GPIO numbers in debugfs output of controller
drivers
- extend the gpio-regmap helper with a new config option and improve its
support for GPIO interrupts
- remove redundant fast_io parameter from regmap configs in GPIO drivers
that already use MMIO regmaps which imply it
- add support for a new model in gpio-mmio: ixp4xx expansion bus
- order includes alphabetically in a few drivers for better readability
- use generic device properties where applicable
- use devm_mutex_init() where applicable
- extend build coverage of drivers by enabling more to be compiled with
COMPILE_TEST enabled
- allow building gpio-stmpe as a module
- use dev_err_probe() where it makes sense in drivers
Late driver fixes:
- fix setting GPIO direction to output in gpio-mpfs
Documentation:
- document the usage of software nodes with GPIO chips
Device-tree bindings:
- Add DT bindings documents for new hardware: Tegra256, MAX7360
- Document a new model in Loongson bindings: LS2K0300
- Document a new model using the generic GPIO binding: IXP4xx
- Convert the DT binding for fsl,mxs-pinctrl to YAML
- fix the schema ID in the "trivial" GPIO schema
- describe GPIO hogs in the generic GPIO binding
-----BEGIN PGP SIGNATURE-----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=TZ1G
-----END PGP SIGNATURE-----
Merge tag 'gpio-updates-for-v6.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio updates from Bartosz Golaszewski:
"There are two new drivers and support for more models in existing
ones.
The generic GPIO API has been reworked and all users converted
which allowed us to move the fields specific to the generic GPIO
implementation out of the high-level struct gpio_chip into its own
structure that wraps the gpio_chip.
Other than that, there's nothing too exciting. Mostly minor tweaks and
fixes all over the place, some refactoring and some small new features
in helper modules.
GPIO core:
- add support for sparse pin ranges to the glue between GPIO and
pinctrl
- use a common prefix across all GPIO descriptor flags for improved
namespacing
New drivers:
- add new GPIO driver for the Nuvoton NCT6694
- add new GPIO driver for MAX7360
Driver improvements:
- add support for Tegra 256 to the gpio-tegra186 driver
- add support for Loongson-2K0300 to the gpio-loongson-64bit driver
- refactor the gpio-aggregator module to expose its GPIO forwarder
API to other in-kernel users (to enable merging of a new pinctrl
driver that uses it)
- convert all remaining drivers to using the modernized generic GPIO
chip API and remove the old interface
- stop displaying global GPIO numbers in debugfs output of controller
drivers
- extend the gpio-regmap helper with a new config option and improve
its support for GPIO interrupts
- remove redundant fast_io parameter from regmap configs in GPIO
drivers that already use MMIO regmaps which imply it
- add support for a new model in gpio-mmio: ixp4xx expansion bus
- order includes alphabetically in a few drivers for better
readability
- use generic device properties where applicable
- use devm_mutex_init() where applicable
- extend build coverage of drivers by enabling more to be compiled
with COMPILE_TEST enabled
- allow building gpio-stmpe as a module
- use dev_err_probe() where it makes sense in drivers
Late driver fixes:
- fix setting GPIO direction to output in gpio-mpfs
Documentation:
- document the usage of software nodes with GPIO chips
Device-tree bindings:
- Add DT bindings documents for new hardware: Tegra256, MAX7360
- Document a new model in Loongson bindings: LS2K0300
- Document a new model using the generic GPIO binding: IXP4xx
- Convert the DT binding for fsl,mxs-pinctrl to YAML
- fix the schema ID in the "trivial" GPIO schema
- describe GPIO hogs in the generic GPIO binding"
* tag 'gpio-updates-for-v6.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux: (122 commits)
gpio: mpfs: fix setting gpio direction to output
gpio: generic: move GPIO_GENERIC_ flags to the correct header
gpio: generic: rename BGPIOF_ flags to GPIO_GENERIC_
gpio: nomadik: fix the debugfs helper stub
MAINTAINERS: Add entry on MAX7360 driver
input: misc: Add support for MAX7360 rotary
input: keyboard: Add support for MAX7360 keypad
gpio: max7360: Add MAX7360 gpio support
gpio: regmap: Allow to provide init_valid_mask callback
gpio: regmap: Allow to allocate regmap-irq device
pwm: max7360: Add MAX7360 PWM support
pinctrl: Add MAX7360 pinctrl driver
mfd: Add max7360 support
dt-bindings: mfd: gpio: Add MAX7360
rtc: Add Nuvoton NCT6694 RTC support
hwmon: Add Nuvoton NCT6694 HWMON support
watchdog: Add Nuvoton NCT6694 WDT support
can: Add Nuvoton NCT6694 CANFD support
i2c: Add Nuvoton NCT6694 I2C support
gpio: Add Nuvoton NCT6694 GPIO support
...
- powerpc support for BPF arena and arena atomics
- Patches to switch to msi parent domain (per-device MSI domains)
- Add a lock contention tracepoint in the queued spinlock slowpath
- Fixes for underflow in pseries/powernv msi and pci paths
- Switch from legacy-of-mm-gpiochip dependency to platform driver
- Fixes for handling TLB misses
- Introduce support for powerpc papr-hvpipe
- Add vpa-dtl PMU driver for pseries platform
- Misc fixes and cleanups
Thanks to: Aboorva Devarajan, Aditya Bodkhe, Andrew Donnellan, Athira Rajeev, Cédric Le Goater, Christophe Leroy,
Erhard Furtner, Gautam Menghani, Geert Uytterhoeven, Haren Myneni, Hari Bathini, Joe Lawrence, Kajol Jain, Kienan Stewart,
Linus Walleij, Mahesh Salgaonkar, Nam Cao, Nicolas Schier, Nysal Jan K.A., Ritesh Harjani (IBM), Ruben Wauters,
Saket Kumar Bhaskar, Shashank MS, Shrikanth Hegde, Tejas Manhas, Thomas Gleixner, Thomas Huth, Thorsten Blum,
Tyrel Datwyler, Venkat Rao Bagalkote,
-----BEGIN PGP SIGNATURE-----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=U2s/
-----END PGP SIGNATURE-----
Merge tag 'powerpc-6.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Madhavan Srinivasan:
- powerpc support for BPF arena and arena atomics
- Patches to switch to msi parent domain (per-device MSI domains)
- Add a lock contention tracepoint in the queued spinlock slowpath
- Fixes for underflow in pseries/powernv msi and pci paths
- Switch from legacy-of-mm-gpiochip dependency to platform driver
- Fixes for handling TLB misses
- Introduce support for powerpc papr-hvpipe
- Add vpa-dtl PMU driver for pseries platform
- Misc fixes and cleanups
Thanks to Aboorva Devarajan, Aditya Bodkhe, Andrew Donnellan, Athira
Rajeev, Cédric Le Goater, Christophe Leroy, Erhard Furtner, Gautam
Menghani, Geert Uytterhoeven, Haren Myneni, Hari Bathini, Joe Lawrence,
Kajol Jain, Kienan Stewart, Linus Walleij, Mahesh Salgaonkar, Nam Cao,
Nicolas Schier, Nysal Jan K.A., Ritesh Harjani (IBM), Ruben Wauters,
Saket Kumar Bhaskar, Shashank MS, Shrikanth Hegde, Tejas Manhas, Thomas
Gleixner, Thomas Huth, Thorsten Blum, Tyrel Datwyler, and Venkat Rao
Bagalkote.
* tag 'powerpc-6.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (49 commits)
powerpc/pseries: Define __u{8,32} types in papr_hvpipe_hdr struct
genirq/msi: Remove msi_post_free()
powerpc/perf/vpa-dtl: Add documentation for VPA dispatch trace log PMU
powerpc/perf/vpa-dtl: Handle the writing of perf record when aux wake up is needed
powerpc/perf/vpa-dtl: Add support to capture DTL data in aux buffer
powerpc/perf/vpa-dtl: Add support to setup and free aux buffer for capturing DTL data
docs: ABI: sysfs-bus-event_source-devices-vpa-dtl: Document sysfs event format entries for vpa_dtl pmu
powerpc/vpa_dtl: Add interface to expose vpa dtl counters via perf
powerpc/time: Expose boot_tb via accessor
powerpc/32: Remove PAGE_KERNEL_TEXT to fix startup failure
powerpc/fprobe: fix updated fprobe for function-graph tracer
powerpc/ftrace: support CONFIG_FUNCTION_GRAPH_RETVAL
powerpc64/modules: replace stub allocation sentinel with an explicit counter
powerpc64/modules: correctly iterate over stubs in setup_ftrace_ool_stubs
powerpc/ftrace: ensure ftrace record ops are always set for NOPs
powerpc/603: Really copy kernel PGD entries into all PGDIRs
powerpc/8xx: Remove left-over instruction and comments in DataStoreTLBMiss handler
powerpc/pseries: HVPIPE changes to support migration
powerpc/pseries: Enable hvpipe with ibm,set-system-parameter RTAS
powerpc/pseries: Enable HVPIPE event message interrupt
...
-----BEGIN PGP SIGNATURE-----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=fwWe
-----END PGP SIGNATURE-----
Merge tag 'ib-mfd-gpio-input-pinctrl-pwm-v6.18' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd into gpio/for-next
Pull changes from the immutable branch between MFD, GPIO, Input, Pinctrl
and PWM trees containing the GPIO driver for max7360.
-----BEGIN PGP SIGNATURE-----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=DW3r
-----END PGP SIGNATURE-----
Merge tag 'ib-mfd-gpio-hwmon-i2c-can-rtc-watchdog-v6.18' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd into gpio/for-next
Pull changes from the immutable branch between MFD, GPIO, HWMON, I2C,
CAN, RTC and Watchdog trees containing GPIO support for Nuvoton NCT6694.
Add driver for Maxim Integrated MAX7360 GPIO/GPO controller.
Two sets of GPIOs are provided by the device:
- Up to 8 GPIOs, shared with the PWM and rotary encoder functionalities.
These GPIOs also provide interrupts on input changes.
- Up to 6 GPOs, on unused keypad columns pins.
Co-developed-by: Kamel Bouhara <kamel.bouhara@bootlin.com>
Signed-off-by: Kamel Bouhara <kamel.bouhara@bootlin.com>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mathieu Dubois-Briand <mathieu.dubois-briand@bootlin.com>
Link: https://lore.kernel.org/r/20250824-mdb-max7360-support-v14-7-435cfda2b1ea@bootlin.com
Signed-off-by: Lee Jones <lee@kernel.org>
This driver supports GPIO and IRQ functionality for NCT6694 MFD
device based on USB interface.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Ming Yu <a0282524688@gmail.com>
Link: https://lore.kernel.org/r/20250912091952.1169369-3-a0282524688@gmail.com
Signed-off-by: Lee Jones <lee@kernel.org>
Add a a driver for the GPIO auxbus child device of the Intel USBIO USB
IO-expander used by the MIPI cameras on various new (Meteor Lake and
later) Intel laptops.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Co-developed-by: Hans de Goede <hansg@kernel.org>
Signed-off-by: Hans de Goede <hansg@kernel.org>
Signed-off-by: Israel Cepeda <israel.a.cepeda.lopez@intel.com>
Link: https://lore.kernel.org/r/20250911181343.77398-3-hansg@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This controller's input and output logic is similar to previous
generations of SoCs. Additionally, it's capable of interrupt masking,
and could be configured to detect levels and edges, and is supplied with
a distinct reset signal.
The interrupt functionality is implemented through an irqchip, whose
operations are written with previous generation SoCs in mind and could
be reused. Since all Loongson SoCs with similar interrupt capability
(LS2K1500, LS2K2000) support byte-control mode, these operations are for
byte-control mode only for simplicity.
Signed-off-by: Yao Zi <ziyao@disroot.org>
Reviewed-by: Huacai Chen <chenhuacai@loongson.cn>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20250904013438.2405-3-ziyao@disroot.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Update help description with supported ICs from gpio-pca953x.c
Include missing IC names.
Signed-off-by: Akhilesh Patil <akhilesh@ee.iitb.ac.in>
Link: https://lore.kernel.org/r/aLmtOWjAWPtWe/gH@bhairav-test.ee.iitb.ac.in
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Remove legacy-of-mm-gpiochip.h header file. The above mentioned
file provides an OF API that's deprecated. There is no agnostic
alternatives to it and we have to open code the logic which was
hidden behind of_mm_gpiochip_add_data(). Note, most of the GPIO
drivers are using their own labeling schemas and resource retrieval
that only a few may gain of the code deduplication, so whenever
alternative is appear we can move drivers again to use that one.
[text copied from commit 34064c8267 ("powerpc/8xx:
Drop legacy-of-mm-gpiochip.h header")]
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Madhavan Srinivasan <maddy@linux.ibm.com>
Link: https://patch.msgid.link/9652736ef05b94d9113ea5ce7899734ef82343d1.1755520794.git.christophe.leroy@csgroup.eu
Commit a86240a37d ("gpiolib: enable CONFIG_GPIOLIB_LEGACY even for
!GPIOLIB") accidentally pulled all items from within the GPIOLIB submenu
into the main driver menu. Put them back under the top-level GPIO entry.
Suggested-by: Rob Herring <robh@kernel.org>
Fixes: a86240a37d ("gpiolib: enable CONFIG_GPIOLIB_LEGACY even for !GPIOLIB")
Reported-by: Rob Herring <robh@kernel.org>
Closes: https://lore.kernel.org/all/20250813222649.GA965895-robh@kernel.org/
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20250901125513.108691-1-brgl@bgdev.pl
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Add the necessary boilerplate to also make this driver modular.
Keep the subsys_initcall to not change registration order for built-in.
Also add OF match table for module autoloading.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Link: https://lore.kernel.org/r/20250728060544.18169-1-alexander.stein@ew.tq-group.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
A few drivers that use the legacy GPIOLIB interfaces can be enabled
even when GPIOLIB is disabled entirely. With my previous patch this
now causes build failures like:
drivers/nfc/s3fwrn5/uart.c: In function 's3fwrn82_uart_parse_dt':
drivers/nfc/s3fwrn5/uart.c💯14: error: implicit declaration of function 'gpio_is_valid'; did you mean 'uuid_is_valid'? [-Werror=implicit-function-declaration]
These did not show up in my randconfig tests because randconfig almost
always has GPIOLIB selected by some other driver, and I did most
of the testing with follow-up patches that address the failures
properly.
Move the symbol outside of the 'if CONFIG_GPIOLIB' block for the moment
to avoid the build failures. It can be moved back and turned off by
default once all the driver specific changes are merged.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202507261934.yIHeUuEQ-lkp@intel.com/
Fixes: 678bae2eaa ("gpiolib: make legacy interfaces optional")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20250726211053.2226857-1-arnd@kernel.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The traditional interfaces are only used on a small number of ancient
boards. Make these optional now so they can be disabled by default.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Link: https://lore.kernel.org/r/20250722153634.3683927-1-arnd@kernel.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
-----BEGIN PGP SIGNATURE-----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=bazF
-----END PGP SIGNATURE-----
Merge tag 'ib-mfd-gpio-power-soc-v6.17' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd into gpio/for-next
Immutable branch between MFD, GPIO, Power and SoC due for the v6.17 merge window
This driver implements the GPIO service on top of the SMC framework
on Apple Mac machines. In particular, these are the GPIOs present in the
PMU IC which are used to control power to certain on-board devices.
Although the underlying hardware supports various pin config settings
(input/output, open drain, etc.), this driver does not implement that
functionality and leaves it up to the firmware to configure things
properly. We also don't yet support interrupts/events. This is
sufficient for device power control, which is the only thing we need to
support at this point. More features will be implemented when needed.
To our knowledge, only Apple Silicon Macs implement this SMC feature.
Signed-off-by: Hector Martin <marcan@marcan.st>
Reviewed-by: Bartosz Golaszewski <brgl@bgdev.pl>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Sven Peter <sven@kernel.org>
Signed-off-by: "Russell King (Oracle)" <rmk+kernel@armlinux.org.uk>
Reviewed-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Reviewed-by: Neal Gompa <neal@gompa.dev>
Signed-off-by: Sven Peter <sven@kernel.org>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20250610-smc-6-15-v7-6-556cafd771d3@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
Add a Kconfig switch allowing to disable the legacy parts of the GPIO
sysfs interface. This means that even though we keep the
/sys/class/gpio/ directory, it no longer contains the global
export/unexport attribute pair (instead, the user should use the
per-chip export/unpexport) nor the gpiochip$BASE entries. This option
default to y if GPIO sysfs is enabled but we'll default it to n at some
point in the future.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20250704-gpio-sysfs-chip-export-v4-9-9289d8758243@linaro.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The driver works fine as a module, so allowing building as such. This
adds an exit handler to support module unload.
Signed-off-by: Aaron Kling <webgeek1234@gmail.com>
Link: https://lore.kernel.org/r/20250702-gpio-palmas-gpio-v4-1-26ba48252f27@gmail.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Add support for adding GPIs to the event FIFO. This is done by adding
irq_chip support. Like this, one can use the input gpio_keys driver as a
"frontend" device and input handler.
As part of this change, we now implement .request() and .free() as we can't
blindly consume all available pins as GPIOs (example: some pins can be
used for forming a keymap matrix).
Also note that the number of pins can now be obtained from the parent,
top level device. Hence the 'max_gpio' variable can be removed.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20250701-dev-adp5589-fw-v7-15-b1fcfe9e9826@analog.com
Signed-off-by: Lee Jones <lee@kernel.org>
This driver uses gpiochip_irq_reqres() and gpiochip_irq_relres() which
are only built with GPIOLIB_IRQCHIP=y. Add the missing Kconfig select.
Fixes: 2993d2dd8f ("gpio: timberdale: Make irq_chip immutable")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/20250522-gpio-fix-v1-4-98ceae7c4c3c@nxp.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
This driver uses gpiochip_irq_reqres() and gpiochip_irq_relres() which
are only built with GPIOLIB_IRQCHIP=y. Add the missing Kconfig select.
Fixes: 289e42df13 ("gpio: lpc18xx: Make irq_chip immutable")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/20250522-gpio-fix-v1-3-98ceae7c4c3c@nxp.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
This driver uses gpiochip_irq_reqres() and gpiochip_irq_relres() which
are only built with GPIOLIB_IRQCHIP=y. Add the missing Kconfig select.
Fixes: a30be40bf1 ("gpio: grgpio: Make irq_chip immutable")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/20250522-gpio-fix-v1-2-98ceae7c4c3c@nxp.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
This driver uses gpiochip_irq_reqres() and gpiochip_irq_relres() which
are only built with GPIOLIB_IRQCHIP=y. Add the missing Kconfig select.
Fixes: 7b04f98027 ("gpio: bcm-kona: make irq_chip immutable")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/20250522-gpio-fix-v1-1-98ceae7c4c3c@nxp.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
-----BEGIN PGP SIGNATURE-----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=2dKC
-----END PGP SIGNATURE-----
Merge tag 'ib-mfd-gpio-nvmem-v6.16' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd into gpio/for-next
Immutable branch between MFD, GPIO and NVMEM due for the v6.16 merge window
The Maxim MAX77759 is a companion PMIC for USB Type-C applications and
includes Battery Charger, Fuel Gauge, temperature sensors, USB Type-C
Port Controller (TCPC), NVMEM, and a GPIO expander.
This driver supports the GPIO functions using the platform device
registered by the core MFD driver.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Acked-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20250509-max77759-mfd-v10-2-962ac15ee3ef@linaro.org
Signed-off-by: Lee Jones <lee@kernel.org>
Support for building it as a module for use on the Android platform,
because the Android kernel(GKI) doesn't contain board-specific drivers,
it requires that these drivers be built as a module and loaded into the
system.
Signed-off-by: Jindong Yue <jindong.yue@nxp.com>
Link: https://lore.kernel.org/r/20250416062605.1948856-1-jindong.yue@nxp.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
