soc: devicetree updates for 6.16

There are 11 newly supported SoCs, but these are all either new variants of existing designs, or straig reuses of the existing chip in a new package: - RK3562 is a new chip based on the old Cortex-A53 core, apparently a low-cost version of the Cortex-A55 based RK3568/RK3566. - NXP i.MX94 is a minor variation of i.MX93/i.MX95 with a different set of on-chip peripherals. - Renesas RZ/V2N (R9A09G056) is a new member of the larger RZ/V2 family - Amlogic S6/S7/S7D - Samsung Exynos7870 is an older chip similar to Exynos7885 - WonderMedia wm8950 is a minor variation on the wm8850 chip - Amlogic s805y is almost idential to s805x - Allwinner A523 is similar to A527 and T527 - Qualcomm MSM8926 is a variant of MSM8226 - Qualcomm Snapdragon X1P42100 is related to R1E80100 There are also 65 boards, including reference designs for the chips above, this includes - 12 new boards based on TI K3 series chips, most of them from Toradex - 10 devices using Rockchips RK35xx and PX30 chips - 2 phones and 2 laptops based on Qualcomm Snapdragon designs - 10 NXP i.MX8/i.MX9 boards, mostly for embedded/industrial uses - 3 Samsung Galaxy phones based on Exynos7870 - 5 Allwinner based boards using a variety of ARMv8 chips - 9 32-bit machines, each based on a different SoC family Aside from the new hardware, there is the usual set of cleanups and newly added hardware support on existing machines, for a total of 965 devicetree changesets. -----BEGIN PGP SIGNATURE----- iQIzBAABCgAdFiEEo6/YBQwIrVS28WGKmmx57+YAGNkFAmg5zYMACgkQmmx57+YA GNl1Ag/8CX35g42Gwxyr2X8wit+O2eU0axGoxM+SD1cmIcSnutZjMGu17lDGduOO 8FC524yLE6Z9HxAUa2/cd+5fOiJcsd6Ggi5WXEFc+dHz0+P5End2DNsdIANbGcFU OAhCpuSB63/Mb5dcecoUULw+LIXIBffwt3FCJ0AaXFDi4RvWr0WatzQxHk/G63ci IoE5pAs/6W9mFvQ5R8Kt4jKISy1zF3JgqOmzy+JIsczPHlyMsbFosZRDxBWMRDza PenoULO/RSe3k37PGe8XCU1sja0lSCVEeJINUB11mSVGoIKRZ9Wxf57O9J81cEqF 8HiqQ58vA/HpStPKfWZV3rXSlc3U3XGUj0lbG4iUSIOE4gMKnjWbPVuBTrr5mYsc cJ1pnzbZ0gbylufeS088GkCCKY/ej40aH0vLeoXEHwGh9LoWudI2xMrTJgwX5AlM H+X9kmP+JaC/woMmY7fr9XpMYuggraIMvDzI1j3qfohGnAUFCG7kh2IvfqkLNAEM o2dJkI/r/PY+fPeHBPw6EvsP6ZJhcorczwB7CxVEYJ8fqKOOunATs+aECa6HLPpv toh86d9rnKUrR9+hbuxacx5xxE/YT30muzh66lnV2p1rCS1RJcnzhAkFzeFNJEXf lpNLMauW1D3Elmk/qawKIxICazeuh4NJyQtNfdrCt/9hEpnmmeM= =ewvq -----END PGP SIGNATURE----- Merge tag 'soc-dt-6.16' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc Pull SoC devicetree updates from Arnd Bergmann: "There are 11 newly supported SoCs, but these are all either new variants of existing designs, or straight reuses of the existing chip in a new package: - RK3562 is a new chip based on the old Cortex-A53 core, apparently a low-cost version of the Cortex-A55 based RK3568/RK3566. - NXP i.MX94 is a minor variation of i.MX93/i.MX95 with a different set of on-chip peripherals. - Renesas RZ/V2N (R9A09G056) is a new member of the larger RZ/V2 family - Amlogic S6/S7/S7D - Samsung Exynos7870 is an older chip similar to Exynos7885 - WonderMedia wm8950 is a minor variation on the wm8850 chip - Amlogic s805y is almost idential to s805x - Allwinner A523 is similar to A527 and T527 - Qualcomm MSM8926 is a variant of MSM8226 - Qualcomm Snapdragon X1P42100 is related to R1E80100 There are also 65 boards, including reference designs for the chips above, this includes - 12 new boards based on TI K3 series chips, most of them from Toradex - 10 devices using Rockchips RK35xx and PX30 chips - 2 phones and 2 laptops based on Qualcomm Snapdragon designs - 10 NXP i.MX8/i.MX9 boards, mostly for embedded/industrial uses - 3 Samsung Galaxy phones based on Exynos7870 - 5 Allwinner based boards using a variety of ARMv8 chips - 9 32-bit machines, each based on a different SoC family Aside from the new hardware, there is the usual set of cleanups and newly added hardware support on existing machines, for a total of 965 devicetree changesets" * tag 'soc-dt-6.16' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (956 commits) MAINTAINERS, mailmap: update Sven Peter's email address arm64: dts: renesas: rzg3e-smarc-som: Reduce I2C2 clock frequency arm64: dts: nuvoton: Add pinctrl ARM: dts: samsung: sp5v210-aries: Align wifi node name with bindings arm64: dts: blaize-blzp1600: Enable GPIO support dt-bindings: clock: socfpga: convert to yaml arm64: dts: rockchip: move rk3562 pinctrl node outside the soc node arm64: dts: rockchip: fix rk3562 pcie unit addresses arm64: dts: rockchip: move rk3528 pinctrl node outside the soc node arm64: dts: rockchip: remove a double-empty line from rk3576 core dtsi arm64: dts: rockchip: move rk3576 pinctrl node outside the soc node arm64: dts: rockchip: fix rk3576 pcie unit addresses arm64: dts: rockchip: Drop assigned-clock* from cpu nodes on rk3588 arm64: dts: rockchip: Add missing SFC power-domains to rk3576 Revert "arm64: dts: mediatek: mt8390-genio-common: Add firmware-name for scp0" arm64: dts: mediatek: mt8188: Address binding warnings for MDP3 nodes arm64: dts: mt6359: Rename RTC node to match binding expectations arm64: dts: mt8365-evk: Add goodix touchscreen support arm64: dts: mediatek: mt8188: Add missing #reset-cells property arm64: dts: airoha: en7581: Add PCIe nodes to EN7581 SoC evaluation board ...
2026-03-08 03:44:45 +01:00 · 2025-05-31 08:08:56 -07:00 · 2025-05-31 08:08:56 -07:00 · ec71f661a5
commit ec71f661a5
parent f79749a8e4 3f07353e2f
764 changed files with 68379 additions and 8514 deletions
--- a/.mailmap
+++ b/.mailmap
@ -725,6 +725,7 @@ Sven Eckelmann <sven@narfation.org> <sven.eckelmann@gmx.de>
 Sven Eckelmann <sven@narfation.org> <sven.eckelmann@open-mesh.com>
 Sven Eckelmann <sven@narfation.org> <sven.eckelmann@openmesh.com>
 Sven Eckelmann <sven@narfation.org> <sven@open-mesh.com>
+Sven Peter <sven@kernel.org> <sven@svenpeter.dev>
 Takashi YOSHII <takashi.yoshii.zj@renesas.com>
 Tamizh Chelvam Raja <quic_tamizhr@quicinc.com> <tamizhr@codeaurora.org>
 Taniya Das <quic_tdas@quicinc.com> <tdas@codeaurora.org>
--- a/Documentation/devicetree/bindings/arm/altera.yaml
+++ b/Documentation/devicetree/bindings/arm/altera.yaml
@ -47,6 +47,7 @@ properties:
              - novtech,chameleon96
              - samtec,vining
              - terasic,de0-atlas
+              - terasic,de10-nano
              - terasic,socfpga-cyclone5-sockit
          - const: altr,socfpga-cyclone5
          - const: altr,socfpga
--- a/Documentation/devicetree/bindings/arm/altera/socfpga-clk-manager.yaml
+++ b/Documentation/devicetree/bindings/arm/altera/socfpga-clk-manager.yaml
@ -9,20 +9,120 @@ title: Altera SOCFPGA Clock Manager
 maintainers:
  - Dinh Nguyen <dinguyen@kernel.org>

-description: test
+description:
+  This binding describes the Altera SOCFGPA Clock Manager and its associated
+  tree of clocks, pll's, and clock gates for the Cyclone5, Arria5 and Arria10
+  chip families.

 properties:
  compatible:
    items:
      - const: altr,clk-mgr
+
  reg:
    maxItems: 1

+  clocks:
+    type: object
+    additionalProperties: false
+
+    properties:
+      "#address-cells":
+        const: 1
+
+      "#size-cells":
+        const: 0
+
+    patternProperties:
+      "^osc[0-9]$":
+        type: object
+
+      "^[a-z0-9,_]+(clk|pll|clk_gate|clk_divided)(@[a-f0-9]+)?$":
+        type: object
+        $ref: '#/$defs/clock-props'
+        unevaluatedProperties: false
+
+        properties:
+          compatible:
+            enum:
+              - altr,socfpga-pll-clock
+              - altr,socfpga-perip-clk
+              - altr,socfpga-gate-clk
+              - altr,socfpga-a10-pll-clock
+              - altr,socfpga-a10-perip-clk
+              - altr,socfpga-a10-gate-clk
+              - fixed-clock
+
+          clocks:
+            description: one or more phandles to input clock
+            minItems: 1
+            maxItems: 5
+
+          "#address-cells":
+            const: 1
+
+          "#size-cells":
+            const: 0
+
+        patternProperties:
+          "^[a-z0-9,_]+(clk|pll)(@[a-f0-9]+)?$":
+            type: object
+            $ref: '#/$defs/clock-props'
+            unevaluatedProperties: false
+
+            properties:
+              compatible:
+                enum:
+                  - altr,socfpga-perip-clk
+                  - altr,socfpga-gate-clk
+                  - altr,socfpga-a10-perip-clk
+                  - altr,socfpga-a10-gate-clk
+
+              clocks:
+                description: one or more phandles to input clock
+                minItems: 1
+                maxItems: 4
+
+            required:
+              - compatible
+              - clocks
+              - "#clock-cells"
+
+        required:
+          - compatible
+          - "#clock-cells"
+
 required:
  - compatible
+  - reg

 additionalProperties: false

+$defs:
+  clock-props:
+    properties:
+      reg:
+        maxItems: 1
+
+      "#clock-cells":
+        const: 0
+
+      clk-gate:
+        $ref: /schemas/types.yaml#/definitions/uint32-array
+        items:
+          - description: gating register offset
+          - description: bit index
+
+      div-reg:
+        $ref: /schemas/types.yaml#/definitions/uint32-array
+        items:
+          - description: divider register offset
+          - description: bit shift
+          - description: bit width
+
+      fixed-divider:
+        $ref: /schemas/types.yaml#/definitions/uint32
+
 examples:
  - |
    clkmgr@ffd04000 {
--- a/Documentation/devicetree/bindings/arm/amlogic.yaml
+++ b/Documentation/devicetree/bindings/arm/amlogic.yaml
@ -27,6 +27,7 @@ properties:
        items:
          - enum:
              - minix,neo-x8
+              - tcu,fernsehfee3
          - const: amlogic,meson8

      - description: Boards with the Amlogic Meson8m2 SoC
@ -73,6 +74,13 @@ properties:
          - const: amlogic,s805x
          - const: amlogic,meson-gxl

+      - description: Boards with the Amlogic Meson GXL S805Y SoC
+        items:
+          - enum:
+              - xiaomi,aquaman
+          - const: amlogic,s805y
+          - const: amlogic,meson-gxl
+
      - description: Boards with the Amlogic Meson GXL S905W SoC
        items:
          - enum:
@ -237,6 +245,24 @@ properties:
              - amlogic,aq222
          - const: amlogic,s4

+      - description: Boards with the Amlogic S6 S905X5 SoC
+        items:
+          - enum:
+              - amlogic,bl209
+          - const: amlogic,s6
+
+      - description: Boards with the Amlogic S7 S805X3 SoC
+        items:
+          - enum:
+              - amlogic,bp201
+          - const: amlogic,s7
+
+      - description: Boards with the Amlogic S7D S905X5M SoC
+        items:
+          - enum:
+              - amlogic,bm202
+          - const: amlogic,s7d
+
      - description: Boards with the Amlogic T7 A311D2 SoC
        items:
          - enum:
--- a/Documentation/devicetree/bindings/arm/bcm/bcm2835.yaml
+++ b/Documentation/devicetree/bindings/arm/bcm/bcm2835.yaml
@ -52,6 +52,7 @@ properties:
      - description: BCM2837 based Boards
        items:
          - enum:
+              - raspberrypi,2-model-b-rev2
              - raspberrypi,3-model-a-plus
              - raspberrypi,3-model-b
              - raspberrypi,3-model-b-plus
--- a/Documentation/devicetree/bindings/arm/fsl.yaml
+++ b/Documentation/devicetree/bindings/arm/fsl.yaml
@ -1120,6 +1120,12 @@ properties:
          - const: avnet,sm2s-imx8mp              # SM2S-IMX8PLUS SoM
          - const: fsl,imx8mp

+      - description: Boundary Devices Nitrogen8M Plus ENC Carrier Board
+        items:
+          - const: boundary,imx8mp-nitrogen-enc-carrier-board
+          - const: boundary,imx8mp-nitrogen-som
+          - const: fsl,imx8mp
+
      - description: Boundary Device Nitrogen8MP Universal SMARC Carrier Board
        items:
          - const: boundary,imx8mp-nitrogen-smarc-universal-board
@ -1156,6 +1162,13 @@ properties:
          - const: kontron,imx8mp-osm-s               # Kontron i.MX8MP OSM-S SoM
          - const: fsl,imx8mp

+      - description: PHYTEC phyCORE-i.MX8MP FPSC based boards
+        items:
+          - enum:
+              - phytec,imx8mp-libra-rdk-fpsc  # i.MX 8M Plus Libra RDK
+          - const: phytec,imx8mp-phycore-fpsc # phyCORE-i.MX 8M Plus FPSC
+          - const: fsl,imx8mp
+
      - description: PHYTEC phyCORE-i.MX8MP SoM based boards
        items:
          - const: phytec,imx8mp-phyboard-pollux-rdk # phyBOARD-Pollux RDK
@ -1176,6 +1189,12 @@ properties:
          - const: polyhex,imx8mp-debix-som-a       # Polyhex Debix SOM A
          - const: fsl,imx8mp

+      - description: Toradex Boards with SMARC iMX8M Plus Modules
+        items:
+          - const: toradex,smarc-imx8mp-dev # Toradex SMARC iMX8M Plus on Toradex SMARC Development Board
+          - const: toradex,smarc-imx8mp     # Toradex SMARC iMX8M Plus Module
+          - const: fsl,imx8mp
+
      - description: Toradex Boards with Verdin iMX8M Plus Modules
        items:
          - enum:
@ -1333,6 +1352,22 @@ properties:
              - const: tq,imx8qxp-tqma8xqp     # TQ-Systems GmbH TQMa8XQP SOM (with i.MX8QXP)
              - const: fsl,imx8qxp

+      - description:
+          TQMa8XxS is a series of SOM featuring NXP i.MX8X system-on-chip
+          variants. It has the SMARC-2.0 form factor and is designed to be placed on
+          different carrier boards. MB-SMARC-2 is a carrier reference design.
+        oneOf:
+          - items:
+              - enum:
+                  - tq,imx8qxp-tqma8xqps-mb-smarc-2 # TQ-Systems GmbH TQMa8QXPS SOM on MB-SMARC-2
+              - const: tq,imx8qxp-tqma8xqps         # TQ-Systems GmbH TQMa8QXPS SOM
+              - const: fsl,imx8qxp
+          - items:
+              - enum:
+                  - tq,imx8dxp-tqma8xdps-mb-smarc-2 # TQ-Systems GmbH TQMa8XDPS SOM on MB-SMARC-2
+              - const: tq,imx8dxp-tqma8xdps         # TQ-Systems GmbH TQMa8XDPS SOM
+              - const: fsl,imx8dxp
+
      - description: i.MX8ULP based Boards
        items:
          - enum:
@ -1347,6 +1382,12 @@ properties:
              - fsl,imx93-14x14-evk       # i.MX93 14x14 EVK Board
          - const: fsl,imx93

+      - description: i.MX94 based Boards
+        items:
+          - enum:
+              - fsl,imx943-evk            # i.MX943 EVK Board
+          - const: fsl,imx94
+
      - description: i.MX95 based Boards
        items:
          - enum:
@ -1374,12 +1415,16 @@ properties:
          All SOM and CPU variants use the same device tree hence only one
          compatible is needed. Bootloader disables all features not present
          in the assembled SOC.
+          MBa91xxCA mainboard can be used as starterkit for the SOM
+          soldered on an adapter board or for the connector variant
+          to evaluate RGB display support.
          MBa93xxCA mainboard can be used as starterkit for the SOM
          soldered on an adapter board or for the connector variant
          MBa93xxLA mainboard is a single board computer using the solderable
          SOM variant
        items:
          - enum:
+              - tq,imx93-tqma9352-mba91xxca # TQ-Systems GmbH i.MX93 TQMa93xxCA/LA SOM on MBa91xxCA
              - tq,imx93-tqma9352-mba93xxca # TQ-Systems GmbH i.MX93 TQMa93xxCA/LA SOM on MBa93xxCA
              - tq,imx93-tqma9352-mba93xxla # TQ-Systems GmbH i.MX93 TQMa93xxLA SOM on MBa93xxLA SBC
          - const: tq,imx93-tqma9352        # TQ-Systems GmbH i.MX93 TQMa93xxCA/LA SOM
@ -1387,8 +1432,10 @@ properties:

      - description: PHYTEC phyCORE-i.MX93 SoM based boards
        items:
-          - const: phytec,imx93-phyboard-segin # phyBOARD-Segin with i.MX93
-          - const: phytec,imx93-phycore-som    # phyCORE-i.MX93 SoM
+          - enum:
+              - phytec,imx93-phyboard-nash  # phyBOARD-Nash-i.MX93
+              - phytec,imx93-phyboard-segin # phyBOARD-Segin with i.MX93
+          - const: phytec,imx93-phycore-som # phyCORE-i.MX93 SoM
          - const: fsl,imx93

      - description: Variscite VAR-SOM-MX93 based boards
@ -1403,6 +1450,16 @@ properties:
          - const: kontron,imx93-osm-s    # Kontron OSM-S i.MX93 SoM
          - const: fsl,imx93

+      - description:
+          TQMa95xxSA is a series of SOM featuring NXP i.MX95 SoC variants.
+          It has the SMARC form factor and is designed to be placed on
+          different carrier boards. MB-SMARC-2 is a carrier reference design.
+        items:
+          - enum:
+              - tq,imx95-tqma9596sa-mb-smarc-2 # TQ-Systems GmbH i.MX95 TQMa95xxSA SOM on MB-SMARC-2
+          - const: tq,imx95-tqma9596sa         # TQ-Systems GmbH i.MX95 TQMa95xxSA SOM
+          - const: fsl,imx95
+
      - description:
          Freescale Vybrid Platform Device Tree Bindings

--- a/Documentation/devicetree/bindings/arm/intel,socfpga.yaml
+++ b/Documentation/devicetree/bindings/arm/intel,socfpga.yaml
@ -25,6 +25,7 @@ properties:
        items:
          - enum:
              - intel,socfpga-agilex5-socdk
+              - intel,socfpga-agilex5-socdk-nand
          - const: intel,socfpga-agilex5

 additionalProperties: true
--- a/Documentation/devicetree/bindings/arm/mediatek.yaml
+++ b/Documentation/devicetree/bindings/arm/mediatek.yaml
@ -104,6 +104,10 @@ properties:
          - enum:
              - bananapi,bpi-r4
          - const: mediatek,mt7988a
+      - items:
+          - const: bananapi,bpi-r4-2g5
+          - const: bananapi,bpi-r4
+          - const: mediatek,mt7988a
      - items:
          - enum:
              - mediatek,mt8127-moose
@ -285,6 +289,13 @@ properties:
          - const: google,steelix-sku393218
          - const: google,steelix
          - const: mediatek,mt8186
+      - description: Google Ponyta
+        items:
+          - enum:
+              - google,ponyta-sku0
+              - google,ponyta-sku1
+          - const: google,ponyta
+          - const: mediatek,mt8186
      - description: Google Rusty (Lenovo 100e Chromebook Gen 4)
        items:
          - const: google,steelix-sku196609
--- a/Documentation/devicetree/bindings/arm/qcom.yaml
+++ b/Documentation/devicetree/bindings/arm/qcom.yaml
@ -90,6 +90,7 @@ description: |
        sm6350
        sm6375
        sm7125
+        sm7150
        sm7225
        sm7325
        sm8150
@ -1020,6 +1021,7 @@ properties:
      - items:
          - enum:
              - sony,pdx201
+              - xiaomi,ginkgo
              - xiaomi,laurel-sprout
          - const: qcom,sm6125

@ -1039,6 +1041,11 @@ properties:
              - xiaomi,joyeuse
          - const: qcom,sm7125

+      - items:
+          - enum:
+              - google,sunfish
+          - const: qcom,sm7150
+
      - items:
          - enum:
              - fairphone,fp4
@ -1123,14 +1130,18 @@ properties:

      - items:
          - enum:
-              - lenovo,thinkpad-t14s
+              - lenovo,thinkpad-t14s-lcd
+              - lenovo,thinkpad-t14s-oled
+          - const: lenovo,thinkpad-t14s
          - const: qcom,x1e78100
          - const: qcom,x1e80100

      - items:
          - enum:
              - asus,vivobook-s15
+              - asus,zenbook-a14-ux3407ra
              - dell,xps13-9345
+              - hp,elitebook-ultra-g1q
              - hp,omnibook-x14
              - lenovo,yoga-slim7x
              - microsoft,romulus13
@ -1141,6 +1152,7 @@ properties:

      - items:
          - enum:
+              - asus,zenbook-a14-ux3407qa
              - qcom,x1p42100-crd
          - const: qcom,x1p42100

--- a/Documentation/devicetree/bindings/arm/rockchip.yaml
+++ b/Documentation/devicetree/bindings/arm/rockchip.yaml
@ -946,6 +946,11 @@ properties:
          - const: radxa,rock-5b
          - const: rockchip,rk3588

+      - description: Radxa ROCK 5B+
+        items:
+          - const: radxa,rock-5b-plus
+          - const: rockchip,rk3588
+
      - description: Radxa ROCK 5C
        items:
          - const: radxa,rock-5c
@ -1047,6 +1052,11 @@ properties:
          - const: rockchip,rk3399-evb
          - const: rockchip,rk3399

+      - description: Rockchip RK3399 Industry Evaluation board
+        items:
+          - const: rockchip,rk3399-evb-ind
+          - const: rockchip,rk3399
+
      - description: Rockchip RK3399 Sapphire standalone
        items:
          - const: rockchip,rk3399-sapphire
@ -1057,6 +1067,11 @@ properties:
          - const: rockchip,rk3399-sapphire-excavator
          - const: rockchip,rk3399

+      - description: Rockchip RK3562 Evaluation board 2
+        items:
+          - const: rockchip,rk3562-evb2-v10
+          - const: rockchip,rk3562
+
      - description: Rockchip RK3566 BOX Evaluation Demo board
        items:
          - const: rockchip,rk3566-box-demo
@ -1074,7 +1089,9 @@ properties:

      - description: Rockchip RK3588 Evaluation board
        items:
-          - const: rockchip,rk3588-evb1-v10
+          - enum:
+              - rockchip,rk3588-evb1-v10
+              - rockchip,rk3588-evb2-v10
          - const: rockchip,rk3588

      - description: Rockchip RK3588S Evaluation board
@ -1109,6 +1126,24 @@ properties:
              - rockchip,rv1126
              - rockchip,rv1109

+      - description: Theobroma Systems PX30-Cobra
+        items:
+          - enum:
+              - tsd,px30-cobra-ltk050h3146w
+              - tsd,px30-cobra-ltk050h3146w-a2
+              - tsd,px30-cobra-ltk050h3148w
+              - tsd,px30-cobra-ltk500hd1829
+          - const: tsd,px30-cobra
+          - const: rockchip,px30
+
+      - description: Theobroma Systems PX30-PP1516
+        items:
+          - enum:
+              - tsd,px30-pp1516-ltk050h3146w-a2
+              - tsd,px30-pp1516-ltk050h3148w
+          - const: tsd,px30-pp1516
+          - const: rockchip,px30
+
      - description: Theobroma Systems PX30-uQ7 with Haikou baseboard
        items:
          - const: tsd,px30-ringneck-haikou
--- a/Documentation/devicetree/bindings/arm/rockchip/pmu.yaml
+++ b/Documentation/devicetree/bindings/arm/rockchip/pmu.yaml
@ -25,6 +25,7 @@ select:
          - rockchip,rk3288-pmu
          - rockchip,rk3368-pmu
          - rockchip,rk3399-pmu
+          - rockchip,rk3562-pmu
          - rockchip,rk3568-pmu
          - rockchip,rk3576-pmu
          - rockchip,rk3588-pmu
@ -43,6 +44,7 @@ properties:
          - rockchip,rk3288-pmu
          - rockchip,rk3368-pmu
          - rockchip,rk3399-pmu
+          - rockchip,rk3562-pmu
          - rockchip,rk3568-pmu
          - rockchip,rk3576-pmu
          - rockchip,rk3588-pmu
--- a/Documentation/devicetree/bindings/arm/samsung/samsung-boards.yaml
+++ b/Documentation/devicetree/bindings/arm/samsung/samsung-boards.yaml
@ -212,6 +212,14 @@ properties:
              - samsung,exynos7-espresso        # Samsung Exynos7 Espresso
          - const: samsung,exynos7

+      - description: Exynos7870 based boards
+        items:
+          - enum:
+              - samsung,a2corelte               # Samsung Galaxy A2 Core
+              - samsung,j6lte                   # Samsung Galaxy J6
+              - samsung,on7xelte                # Samsung Galaxy J7 Prime
+          - const: samsung,exynos7870
+
      - description: Exynos7885 based boards
        items:
          - enum:
--- a/Documentation/devicetree/bindings/arm/stm32/stm32.yaml
+++ b/Documentation/devicetree/bindings/arm/stm32/stm32.yaml
@ -42,6 +42,10 @@ properties:
              - st,stm32h743i-disco
              - st,stm32h743i-eval
          - const: st,stm32h743
+      - items:
+          - enum:
+              - st,stm32h747i-disco
+          - const: st,stm32h747
      - items:
          - enum:
              - st,stm32h750i-art-pi
@ -184,6 +188,11 @@ properties:
          - const: phytec,phycore-stm32mp157c-som
          - const: st,stm32mp157

+      - description: Ultratronik STM32MP1 SBC based Boards
+        items:
+          - const: ultratronik,stm32mp157c-ultra-fly-sbc
+          - const: st,stm32mp157
+
      - description: ST STM32MP257 based Boards
        items:
          - enum:
--- a/Documentation/devicetree/bindings/arm/sunxi.yaml
+++ b/Documentation/devicetree/bindings/arm/sunxi.yaml
@ -492,6 +492,11 @@ properties:
          - const: lamobo,lamobo-r1
          - const: allwinner,sun7i-a20

+      - description: Liontron H-A133L
+        items:
+          - const: liontron,h-a133l
+          - const: allwinner,sun50i-a100
+
      - description: HAOYU Electronics Marsboard A10
        items:
          - const: haoyu,a10-marsboard
@ -845,6 +850,11 @@ properties:
          - const: allwinner,r7-tv-dongle
          - const: allwinner,sun5i-a10s

+      - description: Radxa Cubie A5E
+        items:
+          - const: radxa,cubie-a5e
+          - const: allwinner,sun55i-a527
+
      - description: Remix Mini PC
        items:
          - const: jide,remix-mini-pc
@ -966,6 +976,11 @@ properties:
          - const: hechuang,x96-mate
          - const: allwinner,sun50i-h616

+      - description: X96Q Pro+
+        items:
+          - const: amediatech,x96q-pro-plus
+          - const: allwinner,sun55i-h728
+
      - description: Xunlong OrangePi
        items:
          - const: xunlong,orangepi
@ -1081,4 +1096,14 @@ properties:
          - const: xunlong,orangepi-zero3
          - const: allwinner,sun50i-h618

+      - description: YuzukiHD Avaota A1
+        items:
+          - const: yuzukihd,avaota-a1
+          - const: allwinner,sun55i-t527
+
+      - description: YuzukiHD Chameleon
+        items:
+          - const: yuzukihd,chameleon
+          - const: allwinner,sun50i-h618
+
 additionalProperties: true
--- a/Documentation/devicetree/bindings/arm/tegra.yaml
+++ b/Documentation/devicetree/bindings/arm/tegra.yaml
@ -52,17 +52,14 @@ properties:
              - nvidia,cardhu-a04
          - const: nvidia,cardhu
          - const: nvidia,tegra30
-      - items:
-          - const: asus,tf201
-          - const: nvidia,tegra30
-      - items:
-          - const: asus,tf300t
-          - const: nvidia,tegra30
-      - items:
-          - const: asus,tf300tg
-          - const: nvidia,tegra30
-      - items:
-          - const: asus,tf700t
+      - description: ASUS Transformers Device family
+        items:
+          - enum:
+              - asus,tf201
+              - asus,tf300t
+              - asus,tf300tg
+              - asus,tf300tl
+              - asus,tf700t
          - const: nvidia,tegra30
      - description: LG Optimus 4X P880
        items:
--- a/Documentation/devicetree/bindings/arm/ti/k3.yaml
+++ b/Documentation/devicetree/bindings/arm/ti/k3.yaml
@ -46,6 +46,7 @@ properties:
      - description: K3 AM625 SoC
        items:
          - enum:
+              - beagle,am62-pocketbeagle2
              - beagle,am625-beagleplay
              - ti,am625-sk
              - ti,am62-lp-sk
@ -75,6 +76,30 @@ properties:
          - const: toradex,verdin-am62          # Verdin AM62 Module
          - const: ti,am625

+      - description: K3 AM62P5 SoC Toradex Verdin Modules and Carrier Boards
+        items:
+          - enum:
+              - toradex,verdin-am62p-nonwifi-dahlia # Verdin AM62P Module on Dahlia
+              - toradex,verdin-am62p-nonwifi-dev    # Verdin AM62P Module on Verdin Development Board
+              - toradex,verdin-am62p-nonwifi-ivy    # Verdin AM62P Module on Ivy
+              - toradex,verdin-am62p-nonwifi-mallow # Verdin AM62P Module on Mallow
+              - toradex,verdin-am62p-nonwifi-yavia  # Verdin AM62P Module on Yavia
+          - const: toradex,verdin-am62p-nonwifi     # Verdin AM62P Module without Wi-Fi / BT
+          - const: toradex,verdin-am62p             # Verdin AM62P Module
+          - const: ti,am62p5
+
+      - description: K3 AM62P5 SoC Toradex Verdin Modules and Carrier Boards with Wi-Fi / BT
+        items:
+          - enum:
+              - toradex,verdin-am62p-wifi-dahlia # Verdin AM62P Wi-Fi / BT Module on Dahlia
+              - toradex,verdin-am62p-wifi-dev    # Verdin AM62P Wi-Fi / BT M. on Verdin Development B.
+              - toradex,verdin-am62p-wifi-ivy    # Verdin AM62P Wi-Fi / BT Module on Ivy
+              - toradex,verdin-am62p-wifi-mallow # Verdin AM62P Wi-Fi / BT Module on Mallow
+              - toradex,verdin-am62p-wifi-yavia  # Verdin AM62P Wi-Fi / BT Module on Yavia
+          - const: toradex,verdin-am62p-wifi     # Verdin AM62P Wi-Fi / BT Module
+          - const: toradex,verdin-am62p          # Verdin AM62P Module
+          - const: ti,am62p5
+
      - description: K3 AM642 SoC
        items:
          - enum:
@ -139,6 +164,13 @@ properties:
              - ti,j721s2-evm
          - const: ti,j721s2

+      - description: K3 J721s2 SoC Phytec SoM based boards
+        items:
+          - enum:
+              - phytec,am68-phyboard-izar
+          - const: phytec,am68-phycore-som
+          - const: ti,j721s2
+
      - description: K3 J722S SoC and Boards
        items:
          - enum:
--- a/Documentation/devicetree/bindings/arm/vt8500.yaml
+++ b/Documentation/devicetree/bindings/arm/vt8500.yaml
@ -7,14 +7,13 @@ $schema: http://devicetree.org/meta-schemas/core.yaml#
 title: VIA/Wondermedia VT8500 Platforms

 maintainers:
-  - Tony Prisk <linux@prisktech.co.nz>
-description: test
+  - Alexey Charkov <alchark@gmail.com>

 properties:
  $nodename:
    const: '/'
  compatible:
-    items:
+    oneOf:
      - enum:
          - via,vt8500
          - wm,wm8505
@ -22,4 +21,9 @@ properties:
          - wm,wm8750
          - wm,wm8850

+      - description: VIA APC Rock and Paper boards
+        items:
+          - const: via,apc-rock
+          - const: wm,wm8950
+
 additionalProperties: true
--- a/Documentation/devicetree/bindings/clock/altr_socfpga.txt
+++ b/Documentation/devicetree/bindings/clock/altr_socfpga.txt
@ -1,30 +0,0 @@
-Device Tree Clock bindings for Altera's SoCFPGA platform
-
-This binding uses the common clock binding[1].
-
-[1] Documentation/devicetree/bindings/clock/clock-bindings.txt
-
-Required properties:
- compatible : shall be one of the following:
-	"altr,socfpga-pll-clock" - for a PLL clock
-	"altr,socfpga-perip-clock" - The peripheral clock divided from the
-		PLL clock.
-	"altr,socfpga-gate-clk" - Clocks that directly feed peripherals and
-		can get gated.
-
- reg : shall be the control register offset from CLOCK_MANAGER's base for the clock.
- clocks : shall be the input parent clock phandle for the clock. This is
-	either an oscillator or a pll output.
- #clock-cells : from common clock binding, shall be set to 0.
-
-Optional properties:
- fixed-divider : If clocks have a fixed divider value, use this property.
- clk-gate : For "socfpga-gate-clk", clk-gate contains the gating register
-        and the bit index.
- div-reg : For "socfpga-gate-clk" and "socfpga-periph-clock", div-reg contains
-	the divider register, bit shift, and width.
- clk-phase : For the sdmmc_clk, contains the value of the clock phase that controls
-	the SDMMC CIU clock. The first value is the clk_sample(smpsel), and the second
-	value is the cclk_in_drv(drvsel). The clk-phase is used to enable the correct
-	hold/delay times that is needed for the SD/MMC CIU clock. The values of both
-	can be 0-315 degrees, in 45 degree increments.
--- a/Documentation/devicetree/bindings/display/mediatek/mediatek,aal.yaml
+++ b/Documentation/devicetree/bindings/display/mediatek/mediatek,aal.yaml
@ -25,6 +25,10 @@ properties:
          - mediatek,mt8173-disp-aal
          - mediatek,mt8183-disp-aal
          - mediatek,mt8195-mdp3-aal
+      - items:
+          - enum:
+              - mediatek,mt8188-mdp3-aal
+          - const: mediatek,mt8195-mdp3-aal
      - items:
          - enum:
              - mediatek,mt2712-disp-aal
--- a/Documentation/devicetree/bindings/display/mediatek/mediatek,color.yaml
+++ b/Documentation/devicetree/bindings/display/mediatek/mediatek,color.yaml
@ -27,6 +27,10 @@ properties:
          - mediatek,mt8167-disp-color
          - mediatek,mt8173-disp-color
          - mediatek,mt8195-mdp3-color
+      - items:
+          - enum:
+              - mediatek,mt8188-mdp3-color
+          - const: mediatek,mt8195-mdp3-color
      - items:
          - enum:
              - mediatek,mt7623-disp-color
--- a/Documentation/devicetree/bindings/display/mediatek/mediatek,merge.yaml
+++ b/Documentation/devicetree/bindings/display/mediatek/mediatek,merge.yaml
@ -25,6 +25,10 @@ properties:
          - mediatek,mt8173-disp-merge
          - mediatek,mt8195-disp-merge
          - mediatek,mt8195-mdp3-merge
+      - items:
+          - enum:
+              - mediatek,mt8188-mdp3-merge
+          - const: mediatek,mt8195-mdp3-merge
      - items:
          - const: mediatek,mt6795-disp-merge
          - const: mediatek,mt8173-disp-merge
--- a/Documentation/devicetree/bindings/display/mediatek/mediatek,padding.yaml
+++ b/Documentation/devicetree/bindings/display/mediatek/mediatek,padding.yaml
@ -20,9 +20,13 @@ description:

 properties:
  compatible:
-    enum:
-      - mediatek,mt8188-disp-padding
-      - mediatek,mt8195-mdp3-padding
+    oneOf:
+      - enum:
+          - mediatek,mt8188-disp-padding
+          - mediatek,mt8195-mdp3-padding
+      - items:
+          - const: mediatek,mt8188-mdp3-padding
+          - const: mediatek,mt8195-mdp3-padding

  reg:
    maxItems: 1
--- a/Documentation/devicetree/bindings/dma/nvidia,tegra20-apbdma.txt
+++ b/Documentation/devicetree/bindings/dma/nvidia,tegra20-apbdma.txt
@ -1,44 +0,0 @@
-* NVIDIA Tegra APB DMA controller
-
-Required properties:
- compatible: Should be "nvidia,<chip>-apbdma"
- reg: Should contain DMA registers location and length. This should include
-  all of the per-channel registers.
- interrupts: Should contain all of the per-channel DMA interrupts.
- clocks: Must contain one entry, for the module clock.
-  See ../clocks/clock-bindings.txt for details.
- resets : Must contain an entry for each entry in reset-names.
-  See ../reset/reset.txt for details.
- reset-names : Must include the following entries:
-  - dma
- #dma-cells : Must be <1>. This dictates the length of DMA specifiers in
-  client nodes' dmas properties. The specifier represents the DMA request
-  select value for the peripheral. For more details, consult the Tegra TRM's
-  documentation of the APB DMA channel control register REQ_SEL field.
-
-Examples:
-
-apbdma: dma@6000a000 {
-	compatible = "nvidia,tegra20-apbdma";
-	reg = <0x6000a000 0x1200>;
-	interrupts = < 0 136 0x04
-		       0 137 0x04
-		       0 138 0x04
-		       0 139 0x04
-		       0 140 0x04
-		       0 141 0x04
-		       0 142 0x04
-		       0 143 0x04
-		       0 144 0x04
-		       0 145 0x04
-		       0 146 0x04
-		       0 147 0x04
-		       0 148 0x04
-		       0 149 0x04
-		       0 150 0x04
-		       0 151 0x04 >;
-	clocks = <&tegra_car 34>;
-	resets = <&tegra_car 34>;
-	reset-names = "dma";
-	#dma-cells = <1>;
-};
--- a/Documentation/devicetree/bindings/dma/nvidia,tegra20-apbdma.yaml
+++ b/Documentation/devicetree/bindings/dma/nvidia,tegra20-apbdma.yaml
@ -0,0 +1,90 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/dma/nvidia,tegra20-apbdma.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: NVIDIA Tegra APB DMA Controller
+
+description:
+  The NVIDIA Tegra APB DMA controller is a hardware component that
+  enables direct memory access (DMA) on Tegra systems. It facilitates
+  data transfer between I/O devices and main memory without constant
+  CPU intervention.
+
+maintainers:
+  - Jonathan Hunter <jonathanh@nvidia.com>
+
+properties:
+  compatible:
+    oneOf:
+      - const: nvidia,tegra20-apbdma
+      - items:
+          - const: nvidia,tegra30-apbdma
+          - const: nvidia,tegra20-apbdma
+
+  reg:
+    maxItems: 1
+
+  "#dma-cells":
+    const: 1
+
+  clocks:
+    maxItems: 1
+
+  interrupts:
+    description:
+      Should contain all of the per-channel DMA interrupts in
+      ascending order with respect to the DMA channel index.
+    minItems: 1
+    maxItems: 32
+
+  resets:
+    maxItems: 1
+
+  reset-names:
+    const: dma
+
+required:
+  - compatible
+  - reg
+  - "#dma-cells"
+  - clocks
+  - interrupts
+  - resets
+  - reset-names
+
+allOf:
+  - $ref: dma-controller.yaml#
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    #include <dt-bindings/reset/tegra186-reset.h>
+    dma-controller@6000a000 {
+        compatible = "nvidia,tegra30-apbdma", "nvidia,tegra20-apbdma";
+        reg = <0x6000a000 0x1200>;
+        interrupts = <GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>,
+                     <GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>,
+                     <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>,
+                     <GIC_SPI 139 IRQ_TYPE_LEVEL_HIGH>,
+                     <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>,
+                     <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>,
+                     <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>,
+                     <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>,
+                     <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>,
+                     <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>,
+                     <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>,
+                     <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>,
+                     <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>,
+                     <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>,
+                     <GIC_SPI 150 IRQ_TYPE_LEVEL_HIGH>,
+                     <GIC_SPI 151 IRQ_TYPE_LEVEL_HIGH>;
+        clocks = <&tegra_car 34>;
+        resets = <&tegra_car 34>;
+        reset-names = "dma";
+        #dma-cells = <1>;
+    };
+...
--- a/Documentation/devicetree/bindings/firmware/intel,stratix10-svc.txt
+++ b/Documentation/devicetree/bindings/firmware/intel,stratix10-svc.txt
@ -1,57 +0,0 @@
-Intel Service Layer Driver for Stratix10 SoC
-============================================
-Intel Stratix10 SoC is composed of a 64 bit quad-core ARM Cortex A53 hard
-processor system (HPS) and Secure Device Manager (SDM). When the FPGA is
-configured from HPS, there needs to be a way for HPS to notify SDM the
-location and size of the configuration data. Then SDM will get the
-configuration data from that location and perform the FPGA configuration.
-
-To meet the whole system security needs and support virtual machine requesting
-communication with SDM, only the secure world of software (EL3, Exception
-Layer 3) can interface with SDM. All software entities running on other
-exception layers must channel through the EL3 software whenever it needs
-service from SDM.
-
-Intel Stratix10 service layer driver, running at privileged exception level
-(EL1, Exception Layer 1), interfaces with the service providers and provides
-the services for FPGA configuration, QSPI, Crypto and warm reset. Service layer
-driver also manages secure monitor call (SMC) to communicate with secure monitor
-code running in EL3.
-
-Required properties:
-------------------
-The svc node has the following mandatory properties, must be located under
-the firmware node.
-
- compatible: "intel,stratix10-svc" or "intel,agilex-svc"
- method: smc or hvc
-        smc - Secure Monitor Call
-        hvc - Hypervisor Call
- memory-region:
-	phandle to the reserved memory node. See
-	Documentation/devicetree/bindings/reserved-memory/reserved-memory.txt
-	for details
-
-Example:
-------
-
-	reserved-memory {
-                #address-cells = <2>;
-                #size-cells = <2>;
-                ranges;
-
-                service_reserved: svcbuffer@0 {
-                        compatible = "shared-dma-pool";
-                        reg = <0x0 0x0 0x0 0x1000000>;
-                        alignment = <0x1000>;
-                        no-map;
-                };
-        };
-
-	firmware {
-		svc {
-			compatible = "intel,stratix10-svc";
-			method = "smc";
-			memory-region = <&service_reserved>;
-		};
-	};
--- a/Documentation/devicetree/bindings/firmware/intel,stratix10-svc.yaml
+++ b/Documentation/devicetree/bindings/firmware/intel,stratix10-svc.yaml
@ -0,0 +1,93 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/firmware/intel,stratix10-svc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Intel Service Layer Driver for Stratix10 SoC
+
+maintainers:
+  - Dinh Nguyen <dinguyen@kernel.org>
+  - Mahesh Rao <mahesh.rao@altera.com>
+
+description: >
+  Intel Stratix10 SoC is composed of a 64 bit quad-core ARM Cortex A53 hard
+  processor system (HPS) and Secure Device Manager (SDM). When the FPGA is
+  configured from HPS, there needs to be a way for HPS to notify SDM the
+  location and size of the configuration data. Then SDM will get the
+  configuration data from that location and perform the FPGA configuration.
+
+  To meet the whole system security needs and support virtual machine requesting
+  communication with SDM, only the secure world of software (EL3, Exception
+  Layer 3) can interface with SDM. All software entities running on other
+  exception layers must channel through the EL3 software whenever it needs
+  service from SDM.
+
+  Intel Stratix10 service layer driver, running at privileged exception level
+  (EL1, Exception Layer 1), interfaces with the service providers and provides
+  the services for FPGA configuration, QSPI, Crypto and warm reset. Service layer
+  driver also manages secure monitor call (SMC) to communicate with secure monitor
+  code running in EL3.
+
+properties:
+  compatible:
+    enum:
+      - intel,stratix10-svc
+      - intel,agilex-svc
+
+  method:
+    description: |
+      Supervisory call method to be used to communicate with the
+      secure service layer.
+      Permitted values are:
+      - "smc" : SMC #0, following the SMCCC
+      - "hvc" : HVC #0, following the SMCCC
+
+    $ref: /schemas/types.yaml#/definitions/string-array
+    enum:
+      - smc
+      - hvc
+
+  memory-region:
+    maxItems: 1
+    description:
+      reserved memory region for the service layer driver to
+      communicate with the secure device manager.
+
+  fpga-mgr:
+    $ref: /schemas/fpga/intel,stratix10-soc-fpga-mgr.yaml
+    description: Optional child node for fpga manager to perform fabric configuration.
+
+required:
+  - compatible
+  - method
+  - memory-region
+
+additionalProperties: false
+
+examples:
+  - |
+    reserved-memory {
+      #address-cells = <2>;
+      #size-cells = <2>;
+
+      service_reserved: svcbuffer@0 {
+              compatible = "shared-dma-pool";
+              reg = <0x0 0x0 0x0 0x1000000>;
+              alignment = <0x1000>;
+              no-map;
+      };
+    };
+
+    firmware {
+      svc {
+        compatible = "intel,stratix10-svc";
+        method = "smc";
+        memory-region = <&service_reserved>;
+
+        fpga-mgr {
+          compatible = "intel,stratix10-soc-fpga-mgr";
+        };
+      };
+    };
+
--- a/Documentation/devicetree/bindings/fpga/intel,stratix10-soc-fpga-mgr.yaml
+++ b/Documentation/devicetree/bindings/fpga/intel,stratix10-soc-fpga-mgr.yaml
@ -0,0 +1,36 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/fpga/intel,stratix10-soc-fpga-mgr.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Intel Stratix10 SoC FPGA Manager
+
+maintainers:
+  - Mahesh Rao <mahesh.rao@altera.com>
+  - Adrian Ng Ho Yin <adrian.ho.yin.ng@altera.com>
+  - Niravkumar L Rabara <nirav.rabara@altera.com>
+
+description:
+  The Intel Stratix10 SoC consists of a 64-bit quad-core ARM Cortex A53 hard
+  processor system (HPS) and a Secure Device Manager (SDM). The Stratix10
+  SoC FPGA Manager driver is used to configure/reconfigure the FPGA fabric
+  on the die.The driver communicates with SDM/ATF via the stratix10-svc
+  platform driver for performing its operations.
+
+properties:
+  compatible:
+    enum:
+      - intel,stratix10-soc-fpga-mgr
+      - intel,agilex-soc-fpga-mgr
+
+required:
+  - compatible
+
+additionalProperties: false
+
+examples:
+  - |
+    fpga-mgr {
+      compatible = "intel,stratix10-soc-fpga-mgr";
+    };
--- a/Documentation/devicetree/bindings/fpga/intel-stratix10-soc-fpga-mgr.txt
+++ b/Documentation/devicetree/bindings/fpga/intel-stratix10-soc-fpga-mgr.txt
@ -1,18 +0,0 @@
-Intel Stratix10 SoC FPGA Manager
-
-Required properties:
-The fpga_mgr node has the following mandatory property, must be located under
-firmware/svc node.
-
- compatible : should contain "intel,stratix10-soc-fpga-mgr" or
-	       "intel,agilex-soc-fpga-mgr"
-
-Example:
-
-	firmware {
-		svc {
-			fpga_mgr: fpga-mgr {
-				compatible = "intel,stratix10-soc-fpga-mgr";
-			};
-		};
-	};
--- a/Documentation/devicetree/bindings/interrupt-controller/nvidia,tegra20-ictlr.txt
+++ b/Documentation/devicetree/bindings/interrupt-controller/nvidia,tegra20-ictlr.txt
@ -1,41 +0,0 @@
-NVIDIA Legacy Interrupt Controller
-
-All Tegra SoCs contain a legacy interrupt controller that routes
-interrupts to the GIC, and also serves as a wakeup source. It is also
-referred to as "ictlr", hence the name of the binding.
-
-The HW block exposes a number of interrupt controllers, each
-implementing a set of 32 interrupts.
-
-Required properties:
-
- compatible : should be: "nvidia,tegra<chip>-ictlr". The LIC on
-  subsequent SoCs remained backwards-compatible with Tegra30, so on
-  Tegra generations later than Tegra30 the compatible value should
-  include "nvidia,tegra30-ictlr".	
- reg : Specifies base physical address and size of the registers.
-  Each controller must be described separately (Tegra20 has 4 of them,
-  whereas Tegra30 and later have 5).
- interrupt-controller : Identifies the node as an interrupt controller.
- #interrupt-cells : Specifies the number of cells needed to encode an
-  interrupt source. The value must be 3.
-
-Notes:
-
- Because this HW ultimately routes interrupts to the GIC, the
-  interrupt specifier must be that of the GIC.
- Only SPIs can use the ictlr as an interrupt parent. SGIs and PPIs
-  are explicitly forbidden.
-
-Example:
-
-	ictlr: interrupt-controller@60004000 {
-		compatible = "nvidia,tegra20-ictlr", "nvidia,tegra-ictlr";
-		reg = <0x60004000 64>,
-		      <0x60004100 64>,
-		      <0x60004200 64>,
-		      <0x60004300 64>;
-		interrupt-controller;
-		#interrupt-cells = <3>;
-		interrupt-parent = <&intc>;
-	};
--- a/Documentation/devicetree/bindings/interrupt-controller/nvidia,tegra20-ictlr.yaml
+++ b/Documentation/devicetree/bindings/interrupt-controller/nvidia,tegra20-ictlr.yaml
@ -0,0 +1,82 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/interrupt-controller/nvidia,tegra20-ictlr.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: NVIDIA Tegra20 Legacy Interrupt Controller
+
+maintainers:
+  - Thierry Reding <treding@nvidia.com>
+  - Jonathan Hunter <jonathanh@nvidia.com>
+
+description: >
+  All Tegra SoCs contain a legacy interrupt controller that routes interrupts to
+  the GIC, and also serves as a wakeup source. It is also referred to as
+  "ictlr", hence the name of the binding.
+
+  The HW block exposes a number of interrupt controllers, each implementing a
+  set of 32 interrupts.
+
+  Notes:
+    - Because this HW ultimately routes interrupts to the GIC, the
+      interrupt specifier must be that of the GIC.
+    - Only SPIs can use the ictlr as an interrupt parent. SGIs and PPIs
+      are explicitly forbidden.
+
+properties:
+  compatible:
+    oneOf:
+      - items:
+          - enum:
+              - nvidia,tegra114-ictlr
+              - nvidia,tegra124-ictlr
+          - const: nvidia,tegra30-ictlr
+      - enum:
+          - nvidia,tegra20-ictlr
+          - nvidia,tegra30-ictlr
+
+  reg:
+    description: Each entry is a block of 32 interrupts
+    minItems: 4
+    maxItems: 5
+
+  interrupt-controller: true
+
+  '#interrupt-cells':
+    const: 3
+
+required:
+  - compatible
+  - reg
+  - interrupt-controller
+  - '#interrupt-cells'
+
+additionalProperties: false
+
+allOf:
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: nvidia,tegra20-ictlr
+    then:
+      properties:
+        reg:
+          maxItems: 4
+    else:
+      properties:
+        reg:
+          minItems: 5
+
+examples:
+  - |
+    interrupt-controller@60004000 {
+        compatible = "nvidia,tegra20-ictlr";
+        reg = <0x60004000 64>,
+              <0x60004100 64>,
+              <0x60004200 64>,
+              <0x60004300 64>;
+        interrupt-controller;
+        #interrupt-cells = <3>;
+    };
--- a/Documentation/devicetree/bindings/media/mediatek,mdp3-fg.yaml
+++ b/Documentation/devicetree/bindings/media/mediatek,mdp3-fg.yaml
@ -16,8 +16,12 @@ description:

 properties:
  compatible:
-    enum:
-      - mediatek,mt8195-mdp3-fg
+    oneOf:
+      - enum:
+          - mediatek,mt8195-mdp3-fg
+      - items:
+          - const: mediatek,mt8188-mdp3-fg
+          - const: mediatek,mt8195-mdp3-fg

  reg:
    maxItems: 1
--- a/Documentation/devicetree/bindings/media/mediatek,mdp3-hdr.yaml
+++ b/Documentation/devicetree/bindings/media/mediatek,mdp3-hdr.yaml
@ -16,8 +16,12 @@ description:

 properties:
  compatible:
-    enum:
-      - mediatek,mt8195-mdp3-hdr
+    oneOf:
+      - enum:
+          - mediatek,mt8195-mdp3-hdr
+      - items:
+          - const: mediatek,mt8188-mdp3-hdr
+          - const: mediatek,mt8195-mdp3-hdr

  reg:
    maxItems: 1
--- a/Documentation/devicetree/bindings/media/mediatek,mdp3-rsz.yaml
+++ b/Documentation/devicetree/bindings/media/mediatek,mdp3-rsz.yaml
@ -20,6 +20,7 @@ properties:
          - mediatek,mt8183-mdp3-rsz
      - items:
          - enum:
+              - mediatek,mt8188-mdp3-rsz
              - mediatek,mt8195-mdp3-rsz
          - const: mediatek,mt8183-mdp3-rsz

--- a/Documentation/devicetree/bindings/media/mediatek,mdp3-stitch.yaml
+++ b/Documentation/devicetree/bindings/media/mediatek,mdp3-stitch.yaml
@ -16,8 +16,12 @@ description:

 properties:
  compatible:
-    enum:
-      - mediatek,mt8195-mdp3-stitch
+    oneOf:
+      - enum:
+          - mediatek,mt8195-mdp3-stitch
+      - items:
+          - const: mediatek,mt8188-mdp3-stitch
+          - const: mediatek,mt8195-mdp3-stitch

  reg:
    maxItems: 1
--- a/Documentation/devicetree/bindings/media/mediatek,mdp3-tcc.yaml
+++ b/Documentation/devicetree/bindings/media/mediatek,mdp3-tcc.yaml
@ -17,8 +17,12 @@ description:

 properties:
  compatible:
-    enum:
-      - mediatek,mt8195-mdp3-tcc
+    oneOf:
+      - enum:
+          - mediatek,mt8195-mdp3-tcc
+      - items:
+          - const: mediatek,mt8188-mdp3-tcc
+          - const: mediatek,mt8195-mdp3-tcc

  reg:
    maxItems: 1
--- a/Documentation/devicetree/bindings/media/mediatek,mdp3-tdshp.yaml
+++ b/Documentation/devicetree/bindings/media/mediatek,mdp3-tdshp.yaml
@ -16,8 +16,12 @@ description:

 properties:
  compatible:
-    enum:
-      - mediatek,mt8195-mdp3-tdshp
+    oneOf:
+      - enum:
+          - mediatek,mt8195-mdp3-tdshp
+      - items:
+          - const: mediatek,mt8188-mdp3-tdshp
+          - const: mediatek,mt8195-mdp3-tdshp

  reg:
    maxItems: 1
--- a/Documentation/devicetree/bindings/media/mediatek,mdp3-wrot.yaml
+++ b/Documentation/devicetree/bindings/media/mediatek,mdp3-wrot.yaml
@ -20,6 +20,7 @@ properties:
          - mediatek,mt8183-mdp3-wrot
      - items:
          - enum:
+              - mediatek,mt8188-mdp3-wrot
              - mediatek,mt8195-mdp3-wrot
          - const: mediatek,mt8183-mdp3-wrot

--- a/Documentation/devicetree/bindings/soc/renesas/renesas.yaml
+++ b/Documentation/devicetree/bindings/soc/renesas/renesas.yaml
@ -375,6 +375,13 @@ properties:
              - renesas,r8a779g3 # ES3.x
          - const: renesas,r8a779g0

+      - description: R-Car V4H (R8A779G3)
+        items:
+          - enum:
+              - retronix,sparrow-hawk # Sparrow Hawk board
+          - const: renesas,r8a779g3 # ES3.x
+          - const: renesas,r8a779g0
+
      - description: R-Car V4M (R8A779H0)
        items:
          - enum:
@ -585,6 +592,16 @@ properties:
          - const: renesas,r9a09g057h48
          - const: renesas,r9a09g057

+      - description: RZ/T2H (R9A09G077)
+        items:
+          - enum:
+              - renesas,rzt2h-evk # RZ/T2H Evaluation Board
+          - enum:
+              - renesas,r9a09g077m04 # RZ/T2H with Single Cortex-A55 + Dual Cortex-R52 - no security
+              - renesas,r9a09g077m24 # RZ/T2H with Dual Cortex-A55 + Dual Cortex-R52 - no security
+              - renesas,r9a09g077m44 # RZ/T2H with Quad Cortex-A55 + Dual Cortex-R52 - no security
+          - const: renesas,r9a09g077
+
 additionalProperties: true

 ...
--- a/Documentation/devicetree/bindings/soc/rockchip/grf.yaml
+++ b/Documentation/devicetree/bindings/soc/rockchip/grf.yaml
@ -18,6 +18,12 @@ properties:
              - rockchip,rk3528-ioc-grf
              - rockchip,rk3528-vo-grf
              - rockchip,rk3528-vpu-grf
+              - rockchip,rk3562-ioc-grf
+              - rockchip,rk3562-peri-grf
+              - rockchip,rk3562-pipephy-grf
+              - rockchip,rk3562-pmu-grf
+              - rockchip,rk3562-sys-grf
+              - rockchip,rk3562-usbphy-grf
              - rockchip,rk3566-pipe-grf
              - rockchip,rk3568-pcie3-phy-grf
              - rockchip,rk3568-pipe-grf
@ -82,6 +88,7 @@ properties:
              - rockchip,rk3368-pmugrf
              - rockchip,rk3399-grf
              - rockchip,rk3399-pmugrf
+              - rockchip,rk3562-pmu-grf
              - rockchip,rk3568-grf
              - rockchip,rk3568-pmugrf
              - rockchip,rk3576-ioc-grf
--- a/Documentation/devicetree/bindings/soc/ti/ti,j721e-system-controller.yaml
+++ b/Documentation/devicetree/bindings/soc/ti/ti,j721e-system-controller.yaml
@ -26,6 +26,7 @@ properties:
  compatible:
    items:
      - enum:
+          - ti,am654-system-controller
          - ti,j7200-system-controller
          - ti,j721e-system-controller
          - ti,j721s2-system-controller
@ -68,6 +69,23 @@ patternProperties:
    description:
      The node corresponding to SoC chip identification.

+  "^pcie-ctrl@[0-9a-f]+$":
+    type: object
+    description:
+      The node corresponding to PCIe control register.
+
+  "^clock@[0-9a-f]+$":
+    type: object
+    $ref: /schemas/soc/ti/ti,am654-serdes-ctrl.yaml#
+    description:
+      This is the Serdes Control region.
+
+  "^dss-oldi-io-ctrl@[0-9a-f]+$":
+    type: object
+    $ref: /schemas/mfd/syscon.yaml#
+    description:
+      This is the DSS OLDI CTRL region.
+
 required:
  - compatible
  - reg
@ -110,5 +128,10 @@ examples:
            compatible = "ti,am654-chipid";
            reg = <0x14 0x4>;
        };
+
+        pcie0_ctrl: pcie-ctrl@4070 {
+            compatible = "ti,j784s4-pcie-ctrl", "syscon";
+            reg = <0x4070 0x4>;
+        };
    };
 ...
--- a/Documentation/devicetree/bindings/sram/allwinner,sun4i-a10-system-control.yaml
+++ b/Documentation/devicetree/bindings/sram/allwinner,sun4i-a10-system-control.yaml
@ -50,6 +50,7 @@ properties:
          - enum:
              - allwinner,sun50i-a100-system-control
              - allwinner,sun50i-h6-system-control
+              - allwinner,sun55i-a523-system-control
          - const: allwinner,sun50i-a64-system-control

  reg:
--- a/Documentation/devicetree/bindings/usb/cypress,hx3.yaml
+++ b/Documentation/devicetree/bindings/usb/cypress,hx3.yaml
@ -14,9 +14,22 @@ allOf:

 properties:
  compatible:
-    enum:
-      - usb4b4,6504
-      - usb4b4,6506
+    oneOf:
+      - enum:
+          - usb4b4,6504
+          - usb4b4,6506
+      - items:
+          - enum:
+              - usb4b4,6500
+              - usb4b4,6508
+          - const: usb4b4,6504
+      - items:
+          - enum:
+              - usb4b4,6502
+              - usb4b4,6503
+              - usb4b4,6507
+              - usb4b4,650a
+          - const: usb4b4,6506

  reg: true

--- a/Documentation/devicetree/bindings/vendor-prefixes.yaml
+++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml
@ -868,6 +868,8 @@ patternProperties:
    description: Linux-specific binding
  "^linx,.*":
    description: Linx Technologies
+  "^liontron,.*":
+    description: Shenzhen Liontron Technology Co., Ltd
  "^liteon,.*":
    description: LITE-ON Technology Corp.
  "^litex,.*":
@ -1268,6 +1270,8 @@ patternProperties:
    description: Renesas Electronics Corporation
  "^rervision,.*":
    description: Shenzhen Rervision Technology Co., Ltd.
+  "^retronix,.*":
+    description: Retronix Technology Inc.
  "^revotics,.*":
    description: Revolution Robotics, Inc. (Revotics)
  "^rex,.*":
@ -1500,6 +1504,8 @@ patternProperties:
    description: Toby Churchill Ltd.
  "^tcs,.*":
    description: Shenzhen City Tang Cheng Technology Co., Ltd.
+  "^tcu,.*":
+    description: TC Unterhaltungselektronik AG
  "^tdo,.*":
    description: Shangai Top Display Optoelectronics Co., Ltd
  "^team-source-display,.*":
@ -1613,6 +1619,8 @@ patternProperties:
    description: Universal Scientific Industrial Co., Ltd.
  "^usr,.*":
    description: U.S. Robotics Corporation
+  "^ultratronik,.*":
+    description: Ultratronik GmbH
  "^utoo,.*":
    description: Aigo Digital Technology Co., Ltd.
  "^v3,.*":
@ -1755,6 +1763,8 @@ patternProperties:
    description: Y Soft Corporation a.s.
  "^yuridenki,.*":
    description: Yuridenki-Shokai Co. Ltd.
+  "^yuzukihd,.*":
+    description: YuzukiHD Open Source Hardware
  "^zarlink,.*":
    description: Zarlink Semiconductor
  "^zealz,.*":
--- a/9
+++ b/9
@ -2296,7 +2296,7 @@ F:	sound/soc/codecs/cs42l84.*
 F:	sound/soc/codecs/ssm3515.c

 ARM/APPLE MACHINE SUPPORT
-M:	Sven Peter <sven@svenpeter.dev>
+M:	Sven Peter <sven@kernel.org>
 M:	Janne Grunau <j@jannau.net>
 R:	Alyssa Rosenzweig <alyssa@rosenzweig.io>
 R:	Neal Gompa <neal@gompa.dev>
@ -24975,6 +24975,7 @@ F:	arch/arm64/boot/dts/freescale/fsl-*tqml*.dts*
 F:	arch/arm64/boot/dts/freescale/imx*mba*.dts*
 F:	arch/arm64/boot/dts/freescale/imx*tqma*.dts*
 F:	arch/arm64/boot/dts/freescale/mba*.dtsi
+F:	arch/arm64/boot/dts/freescale/tqma8*.dtsi
 F:	arch/arm64/boot/dts/freescale/tqml*.dts*
 F:	drivers/gpio/gpio-tqmx86.c
 F:	drivers/mfd/tqmx86.c
@ -25243,6 +25244,12 @@ S:	Maintained
 F:	drivers/usb/common/ulpi.c
 F:	include/linux/ulpi/

+ULTRATRONIK BOARD SUPPORT
+M:	Goran Rađenović <goran.radni@gmail.com>
+M:	Börge Strümpfel <boerge.struempfel@gmail.com>
+S:	Maintained
+F:	arch/arm/boot/dts/st/stm32mp157c-ultra-fly-sbc.dts
+
 UNICODE SUBSYSTEM
 M:	Gabriel Krisman Bertazi <krisman@kernel.org>
 L:	linux-fsdevel@vger.kernel.org
--- a/arch/arm/boot/dts/allwinner/sun7i-a20-bananapi.dts
+++ b/arch/arm/boot/dts/allwinner/sun7i-a20-bananapi.dts
@ -48,6 +48,7 @@

 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/leds/common.h>

 / {
 	model = "LeMaker Banana Pi";
@ -169,6 +170,32 @@
 &gmac_mdio {
 	phy1: ethernet-phy@1 {
 		reg = <1>;
+
+		leds {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			led@0 {
+				reg = <0>;
+				color = <LED_COLOR_ID_GREEN>;
+				function = LED_FUNCTION_LAN;
+				linux,default-trigger = "netdev";
+			};
+
+			led@1 {
+				reg = <1>;
+				color = <LED_COLOR_ID_AMBER>;
+				function = LED_FUNCTION_LAN;
+				linux,default-trigger = "netdev";
+			};
+
+			led@2 {
+				reg = <2>;
+				color = <LED_COLOR_ID_BLUE>;
+				function = LED_FUNCTION_LAN;
+				linux,default-trigger = "netdev";
+			};
+		};
 	};
 };

--- a/arch/arm/boot/dts/allwinner/sun8i-a83t.dtsi
+++ b/arch/arm/boot/dts/allwinner/sun8i-a83t.dtsi
@ -1225,7 +1225,7 @@
 			};

 			cooling-maps {
-				cpu-hot-limit {
+				map0 {
 					trip = <&cpu0_hot>;
 					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
 							 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
@ -1255,7 +1255,7 @@
 			};

 			cooling-maps {
-				cpu-hot-limit {
+				map0 {
 					trip = <&cpu1_hot>;
 					cooling-device = <&cpu100 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
 							 <&cpu101 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
--- a/arch/arm/boot/dts/allwinner/sun8i-h3-nanopi-neo-air.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-h3-nanopi-neo-air.dts
@ -94,7 +94,7 @@
 	non-removable;
 	status = "okay";

-	brcmf: bcrmf@1 {
+	brcmf: wifi@1 {
 		reg = <1>;
 		compatible = "brcm,bcm4329-fmac";
 		interrupt-parent = <&pio>;
--- a/arch/arm/boot/dts/allwinner/sun8i-h3.dtsi
+++ b/arch/arm/boot/dts/allwinner/sun8i-h3.dtsi
@ -262,7 +262,7 @@
 			};

 			cooling-maps {
-				cpu-hot-limit {
+				map0 {
 					trip = <&cpu_hot_trip>;
 					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
 							 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
--- a/arch/arm/boot/dts/allwinner/sun8i-r40.dtsi
+++ b/arch/arm/boot/dts/allwinner/sun8i-r40.dtsi
@ -146,7 +146,7 @@
 			};

 			cooling-maps {
-				cpu-hot-limit {
+				map0 {
 					trip = <&cpu_hot_trip>;
 					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
 							 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
--- a/arch/arm/boot/dts/amlogic/Makefile
+++ b/arch/arm/boot/dts/amlogic/Makefile
@ -1,6 +1,7 @@
 # SPDX-License-Identifier: GPL-2.0
 dtb-$(CONFIG_MACH_MESON8) += \
 	meson8-minix-neo-x8.dtb \
+	meson8-fernsehfee3.dtb \
 	meson8b-ec100.dtb \
 	meson8b-mxq.dtb \
 	meson8b-odroidc1.dtb \
--- a/arch/arm/boot/dts/amlogic/meson8-fernsehfee3.dts
+++ b/arch/arm/boot/dts/amlogic/meson8-fernsehfee3.dts
@ -0,0 +1,306 @@
+// SPDX-License-Identifier: GPL-2.0-only OR MIT
+// Copyright (C) 2025 J. Neuschäfer <j.ne@posteo.net>
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/leds/common.h>
+
+#include "meson8.dtsi"
+
+/ {
+	model = "Fernsehfee 3.0";
+	compatible = "tcu,fernsehfee3", "amlogic,meson8";
+
+	aliases {
+		serial0 = &uart_AO;
+		gpiochip0 = &gpio;
+		gpiochip1 = &gpio_ao;
+		i2c0 = &i2c_AO;
+		i2c1 = &i2c_B;
+		mmc0 = &sdhc;
+		mmc1 = &sdio;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x40000000>;  /* 1 GiB */
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys-polled";
+		poll-interval = <100>;
+
+		power-button {
+			label = "Power button";
+			linux,code = <KEY_POWER>;
+			gpios = <&gpio_ao GPIOAO_3 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-0 {
+			/*
+			 * The power LED can be turned red, otherwise it is green.
+			 */
+			gpios = <&gpio_ao GPIO_TEST_N GPIO_ACTIVE_LOW>;
+			function = LED_FUNCTION_POWER;
+			color = <LED_COLOR_ID_RED>;
+		};
+	};
+
+	vcc_5v: regulator-5v {
+		/* 5V rail, always on as long as the system is running */
+		compatible = "regulator-fixed";
+		regulator-name = "5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+
+	vcc_3v3: regulator-3v3 {
+		/* Chipown AP2420 step-down converter */
+		compatible = "regulator-fixed";
+		regulator-name = "3.3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcc_5v>;
+	};
+
+	wifi_3v3: regulator-wifi {
+		compatible = "regulator-fixed";
+		regulator-name = "3.3V-WIFI";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcc_3v3>;
+		gpio = <&gpio GPIOX_11 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+};
+
+&cpu0 {
+	cpu-supply = <&vcck>;
+};
+
+&ethmac {
+	status = "okay";
+	pinctrl-0 = <&eth_pins>;
+	pinctrl-names = "default";
+	phy-handle = <&eth_phy0>;
+	phy-mode = "rmii";
+
+	mdio {
+		compatible = "snps,dwmac-mdio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		eth_phy0: ethernet-phy@0 {
+			/* IC Plus IP101A (0x02430c54) */
+			reg = <0>;
+
+			reset-assert-us = <10000>;
+			reset-deassert-us = <10000>;
+			reset-gpios = <&gpio GPIOH_4 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&i2c_AO {
+	status = "okay";
+	pinctrl-0 = <&i2c_ao_pins>;
+	pinctrl-names = "default";
+
+	pmic@32 {
+		compatible = "ricoh,rn5t618";
+		reg = <0x32>;
+		system-power-controller;
+
+		regulators {
+			vcck: DCDC1 {
+				regulator-name = "VCCK";
+				regulator-min-microvolt = <825000>;
+				regulator-max-microvolt = <1150000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			vddee: DCDC2 {
+				/* the output is also used as VDDAO */
+				regulator-name = "VDD_EE";
+				regulator-min-microvolt = <950000>;
+				regulator-max-microvolt = <1150000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			DCDC3 {
+				regulator-name = "VDD_DDR";
+				regulator-min-microvolt = <1500000>;
+				regulator-max-microvolt = <1500000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			LDO1 {
+				regulator-name = "VDDIO_AO28";
+				regulator-min-microvolt = <2900000>;
+				regulator-max-microvolt = <2900000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			LDO2 {
+				regulator-name = "VDDIO_AO18";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			vcc1v8_usb: LDO3 {
+				regulator-name = "VCC1V8_USB";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+			};
+
+			LDO4 {
+				/* This one appears to be unused */
+				regulator-name = "VCC2V8";
+				regulator-min-microvolt = <2850000>;
+				regulator-max-microvolt = <2850000>;
+			};
+
+			LDO5 {
+				regulator-name = "AVDD1V8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			LDORTC1 {
+				regulator-name = "VDD_LDO";
+				regulator-min-microvolt = <2700000>;
+				regulator-max-microvolt = <2700000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			LDORTC2 {
+				regulator-name = "RTC_0V9";
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <900000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+		};
+	};
+
+	eeprom@50 {
+		/* Fairchild FM24C08A */
+		compatible = "atmel,24c08";
+		reg = <0x50>;
+		pagesize = <16>;
+		wp-gpios = <&gpio GPIOH_3 GPIO_ACTIVE_HIGH>;
+		num-addresses = <4>;
+	};
+};
+
+&i2c_B {
+	status = "okay";
+	pinctrl-0 = <&i2c_b_pins>;
+	pinctrl-names = "default";
+
+	/* TODO: SiI9293 HDMI receiver @ 0x39 */
+};
+
+&mali {
+	mali-supply = <&vddee>;
+};
+
+&sdhc {
+	status = "okay";
+	pinctrl-0 = <&sdxc_c_pins>;
+	pinctrl-names = "default";
+
+	/* eMMC */
+	bus-width = <8>;
+	max-frequency = <100000000>;
+
+	disable-wp;
+	cap-mmc-highspeed;
+	mmc-hs200-1_8v;
+	no-sdio;
+
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&vcc_3v3>;
+};
+
+&sdio {
+	status = "okay";
+	pinctrl-0 = <&sd_b_pins>;
+
+	/* SD card */
+	slot@1 {
+		compatible = "mmc-slot";
+		reg = <1>;
+		status = "okay";
+
+		bus-width = <4>;
+		cap-mmc-highspeed;
+		cap-sd-highspeed;
+		disable-wp;
+
+		cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_LOW>;
+
+		vmmc-supply = <&vcc_3v3>;
+	};
+};
+
+&uart_AO {
+	status = "okay";
+	pinctrl-0 = <&uart_ao_a_pins>;
+	pinctrl-names = "default";
+};
+
+&usb0 {
+	status = "okay";
+};
+
+&usb0_phy {
+	status = "okay";
+	phy-supply = <&vcc1v8_usb>;
+};
+
+&usb1 {
+	status = "okay";
+	dr_mode = "host";
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	wifi: wifi@1 {
+		/* Realtek RTL8188 2.4GHz WiFi module */
+		compatible = "usbbda,179";
+		reg = <1>;
+		vdd-supply = <&wifi_3v3>;
+	};
+};
+
+&usb1_phy {
+	status = "okay";
+	phy-supply = <&vcc1v8_usb>;
+};
+
+&ir_receiver {
+	status = "okay";
+	pinctrl-0 = <&ir_recv_pins>;
+	pinctrl-names = "default";
+};
--- a/arch/arm/boot/dts/amlogic/meson8.dtsi
+++ b/arch/arm/boot/dts/amlogic/meson8.dtsi
@ -398,7 +398,7 @@
 			mux {
 				groups = "uart_tx_ao_a", "uart_rx_ao_a";
 				function = "uart_ao";
-				bias-disable;
+				bias-pull-up;
 			};
 		};

@ -481,6 +481,14 @@
 			gpio-ranges = <&pinctrl_cbus 0 0 120>;
 		};

+		i2c_b_pins: i2c-b {
+			mux {
+				groups = "i2c_sda_b", "i2c_sck_b";
+				function = "i2c_b";
+				bias-disable;
+			};
+		};
+
 		sd_a_pins: sd-a {
 			mux {
 				groups = "sd_d0_a", "sd_d1_a", "sd_d2_a",
@ -526,6 +534,16 @@
 			};
 		};

+		sdxc_c_pins: sdxc-c {
+			mux {
+				groups = "sdxc_d0_c", "sdxc_d13_c",
+					"sdxc_clk_c", "sdxc_cmd_c",
+					"sdxc_d47_c";
+				function = "sdxc_c";
+				bias-pull-up;
+			};
+		};
+
 		spdif_out_pins: spdif-out {
 			mux {
 				groups = "spdif_out";
@ -567,7 +585,7 @@
 				groups = "uart_tx_a1",
 				       "uart_rx_a1";
 				function = "uart_a";
-				bias-disable;
+				bias-pull-up;
 			};
 		};

--- a/arch/arm/boot/dts/amlogic/meson8b.dtsi
+++ b/arch/arm/boot/dts/amlogic/meson8b.dtsi
@ -368,7 +368,7 @@
 			mux {
 				groups = "uart_tx_ao_a", "uart_rx_ao_a";
 				function = "uart_ao";
-				bias-disable;
+				bias-pull-up;
 			};
 		};

@ -521,7 +521,7 @@
 				groups = "uart_tx_b0",
 				       "uart_rx_b0";
 				function = "uart_b";
-				bias-disable;
+				bias-pull-up;
 			};
 		};

--- a/arch/arm/boot/dts/broadcom/Makefile
+++ b/arch/arm/boot/dts/broadcom/Makefile
@ -7,6 +7,7 @@ DTC_FLAGS_bcm2835-rpi-b-plus := -@
 DTC_FLAGS_bcm2835-rpi-a-plus := -@
 DTC_FLAGS_bcm2835-rpi-cm1-io1 := -@
 DTC_FLAGS_bcm2836-rpi-2-b := -@
+DTC_FLAGS_bcm2837-rpi-2-b := -@
 DTC_FLAGS_bcm2837-rpi-3-a-plus := -@
 DTC_FLAGS_bcm2837-rpi-3-b := -@
 DTC_FLAGS_bcm2837-rpi-3-b-plus := -@
@ -25,6 +26,7 @@ dtb-$(CONFIG_ARCH_BCM2835) += \
 	bcm2835-rpi-a-plus.dtb \
 	bcm2835-rpi-cm1-io1.dtb \
 	bcm2836-rpi-2-b.dtb \
+	bcm2837-rpi-2-b.dtb \
 	bcm2837-rpi-3-a-plus.dtb \
 	bcm2837-rpi-3-b.dtb \
 	bcm2837-rpi-3-b-plus.dtb \
--- a/arch/arm/boot/dts/broadcom/bcm2166x-common.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm2166x-common.dtsi
@ -46,6 +46,11 @@
 			interrupt-controller;
 		};

+		pinctrl: pinctrl@1004800 {
+			compatible = "brcm,bcm21664-pinctrl";
+			reg = <0x01004800 0x7f4>;
+		};
+
 		timer@1006000 {
 			compatible = "brcm,kona-timer";
 			reg = <0x01006000 0x1c>;
@ -332,3 +337,5 @@
 		};
 	};
 };
+
+#include "bcm2166x-pinctrl.dtsi"
--- a/arch/arm/boot/dts/broadcom/bcm2166x-pinctrl.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm2166x-pinctrl.dtsi
@ -0,0 +1,297 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Common pinmux configrations for BCM2166x (BCM21664/BCM23550).
+ *
+ * Copyright (C) 2025 Artur Weber <aweber.kernel@gmail.com>
+ */
+
+&pinctrl {
+	/* BSC1 */
+	bsc1_pins: bsc1-pins {
+		bsc1clk-grp0 {
+			pins = "bsc1clk";
+			function = "alt1"; /* BSC1CLK */
+		};
+
+		bsc1dat-grp0 {
+			pins = "bsc1dat";
+			function = "alt1"; /* BSC1DAT */
+		};
+	};
+
+	/* BSC2 */
+	bsc2_pins: bsc2-pins {
+		bsc2clk-grp0 {
+			pins = "gpio16";
+			function = "alt2"; /* BSC2CLK */
+		};
+
+		bsc2dat-grp0 {
+			pins = "gpio17";
+			function = "alt2"; /* BSC2DAT */
+		};
+	};
+
+	/* BSC3 */
+	bsc3_pins: bsc3-pins {
+		bsc3clk-grp0 {
+			pins = "lcdscl";
+			function = "alt1"; /* BSC3_CLK */
+		};
+
+		bsc3dat-grp0 {
+			pins = "lcdsda";
+			function = "alt1"; /* BSC3_SDA */
+		};
+	};
+
+	/* BSC4 */
+	bsc4_pins: bsc4-pins {
+		bsc4clk-grp0 {
+			pins = "lcdres";
+			function = "alt1"; /* BSC4_CLK */
+		};
+
+		bsc4dat-grp0 {
+			pins = "lcdte";
+			function = "alt1"; /* BSC4_SDA */
+		};
+	};
+
+	/* PMBSC */
+	pmbsc_pins: pmbsc-pins {
+		pmbscclk-grp0 {
+			pins = "pmbscclk";
+			function = "alt1"; /* PMBSCCLK */
+		};
+
+		pmbscdat-grp0 {
+			pins = "pmbscdat";
+			function = "alt1"; /* PMBSCDAT */
+		};
+	};
+
+	/* SD */
+	sd_width1_pins: sd-width1-pins {
+		sdck-grp0 {
+			pins = "sdck";
+			function = "alt1"; /* SDCK */
+			bias-disable;
+		};
+
+		sdcmd-grp0 {
+			pins = "sdcmd";
+			function = "alt1"; /* SDCMD */
+			bias-pull-up;
+		};
+
+		sddat-grp0 {
+			pins = "sddat0";
+			function = "alt1"; /* SDDATx */
+			bias-pull-up;
+		};
+	};
+
+	sd_width4_pins: sd-width4-pins {
+		sdck-grp0 {
+			pins = "sdck";
+			function = "alt1"; /* SDCK */
+			bias-disable;
+		};
+
+		sdcmd-grp0 {
+			pins = "sdcmd";
+			function = "alt1"; /* SDCMD */
+			bias-pull-up;
+		};
+
+		sddat-grp0 {
+			pins = "sddat0", "sddat1", "sddat2", "sddat3";
+			function = "alt1"; /* SDDATx */
+			bias-pull-up;
+		};
+	};
+
+	/* SD1 */
+	sd1_width1_pins: sd1-width1-pins {
+		sd1ck-grp0 {
+			pins = "mmc1dat7";
+			function = "alt6"; /* SD1CK */
+			bias-disable;
+		};
+
+		sd1cmd-grp0 {
+			pins = "spi0txd";
+			function = "alt2"; /* SD1CMD */
+			bias-pull-up;
+		};
+
+		sd1dat0-grp0 {
+			pins = "mmc1dat5";
+			function = "alt6"; /* SD1DAT0 */
+			bias-pull-up;
+		};
+	};
+
+	sd1_width4_pins: sd1-width4-pins {
+		sd1ck-grp0 {
+			pins = "mmc1dat7";
+			function = "alt6"; /* SD1CK */
+			bias-disable;
+		};
+
+		sd1cmd-grp0 {
+			pins = "spi0txd";
+			function = "alt2"; /* SD1CMD */
+			bias-pull-up;
+		};
+
+		sd1dat0-grp0 {
+			pins = "mmc1dat5";
+			function = "alt6"; /* SD1DAT0 */
+			bias-pull-up;
+		};
+
+		sd1dat1-grp0 {
+			pins = "gpio93";
+			function = "alt1"; /* SD1DAT1 */
+			bias-pull-up;
+		};
+
+		sd1dat2-grp0 {
+			pins = "gpio94";
+			function = "alt1"; /* SD1DAT2 */
+			bias-pull-up;
+		};
+
+		sd1dat3-grp0 {
+			pins = "mmc1dat3";
+			function = "alt6"; /* SD1DAT3 */
+			bias-pull-up;
+		};
+	};
+
+	/* MMC0 */
+	mmc0_width1_pins: mmc0-width1-pins {
+		mmc0ck-grp0 {
+			pins = "mmc0ck";
+			function = "alt1"; /* MMC0CK */
+			bias-disable;
+		};
+
+		mmc0cmd-grp0 {
+			pins = "mmc0cmd";
+			function = "alt1"; /* MMC0CMD */
+			bias-pull-up;
+		};
+
+		mmc0dat-grp0 {
+			pins = "mmc0dat0";
+			function = "alt1"; /* MMC0DATx */
+			bias-pull-up;
+		};
+	};
+
+	mmc0_width4_pins: mmc0-width4-pins {
+		mmc0ck-grp0 {
+			pins = "mmc0ck";
+			function = "alt1"; /* MMC0CK */
+			bias-disable;
+		};
+
+		mmc0cmd-grp0 {
+			pins = "mmc0cmd";
+			function = "alt1"; /* MMC0CMD */
+			bias-pull-up;
+		};
+
+		mmc0dat-grp0 {
+			pins = "mmc0dat0", "mmc0dat1", "mmc0dat2", "mmc0dat3";
+			function = "alt1"; /* MMC0DATx */
+			bias-pull-up;
+		};
+	};
+
+	mmc0_width8_pins: mmc0-width8-pins {
+		mmc0ck-grp0 {
+			pins = "mmc0ck";
+			function = "alt1"; /* MMC0CK */
+			bias-disable;
+		};
+
+		mmc0cmd-grp0 {
+			pins = "mmc0cmd";
+			function = "alt1"; /* MMC0CMD */
+			bias-pull-up;
+		};
+
+		mmc0dat-grp0 {
+			pins = "mmc0dat0", "mmc0dat1", "mmc0dat2", "mmc0dat3",
+			       "mmc0dat4", "mmc0dat5", "mmc0dat6", "mmc0dat7";
+			function = "alt1"; /* MMC0DATx */
+			bias-pull-up;
+		};
+	};
+
+	/* MMC1 */
+	mmc1_width1_pins: mmc1-width1-pins {
+		mmc1ck-grp0 {
+			pins = "mmc1ck";
+			function = "alt1"; /* MMC1CK */
+			bias-disable;
+		};
+
+		mmc1cmd-grp0 {
+			pins = "mmc1cmd";
+			function = "alt1"; /* MMC1CMD */
+			bias-pull-up;
+		};
+
+		mmc1dat-grp0 {
+			pins = "mmc1dat0";
+			function = "alt1"; /* MMC1DATx */
+			bias-pull-up;
+		};
+	};
+
+	mmc1_width4_pins: mmc1-width4-pins {
+		mmc1ck-grp0 {
+			pins = "mmc1ck";
+			function = "alt1"; /* MMC1CK */
+			bias-disable;
+		};
+
+		mmc1cmd-grp0 {
+			pins = "mmc1cmd";
+			function = "alt1"; /* MMC1CMD */
+			bias-pull-up;
+		};
+
+		mmc1dat-grp0 {
+			pins = "mmc1dat0", "mmc1dat1", "mmc1dat2", "mmc1dat3";
+			function = "alt1"; /* MMC1DATx */
+			bias-pull-up;
+		};
+	};
+
+	mmc1_width8_pins: mmc1-width8-pins {
+		mmc1ck-grp0 {
+			pins = "mmc1ck";
+			function = "alt1"; /* MMC1CK */
+			bias-disable;
+		};
+
+		mmc1cmd-grp0 {
+			pins = "mmc1cmd";
+			function = "alt1"; /* MMC1CMD */
+			bias-pull-up;
+		};
+
+		mmc1dat-grp0 {
+			pins = "mmc1dat0", "mmc1dat1", "mmc1dat2", "mmc1dat3",
+			       "mmc1dat4", "mmc1dat5", "mmc1dat6", "mmc1dat7";
+			function = "alt1"; /* MMC1DATx */
+			bias-pull-up;
+		};
+	};
+};
--- a/arch/arm/boot/dts/broadcom/bcm28155-ap.dts
+++ b/arch/arm/boot/dts/broadcom/bcm28155-ap.dts
@ -37,7 +37,39 @@
 	status = "okay";

 	pmu: pmu@8 {
+		compatible = "brcm,bcm59056";
+		interrupts = <GIC_SPI 215 IRQ_TYPE_LEVEL_HIGH>;
 		reg = <0x08>;
+
+		regulators {
+			camldo1_reg: camldo1 {
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			sdldo_reg: sdldo {
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3000000>;
+			};
+
+			sdxldo_reg: sdxldo {
+				regulator-min-microvolt = <2700000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			usbldo_reg: usbldo {
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			iosr1_reg: iosr1 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+			};
+		};
 	};
 };

@ -74,39 +106,3 @@
 &usbphy {
 	status = "okay";
 };
-
-#include "bcm59056.dtsi"
-
-&pmu {
-	compatible = "brcm,bcm59056";
-	interrupts = <GIC_SPI 215 IRQ_TYPE_LEVEL_HIGH>;
-	regulators {
-		camldo1_reg: camldo1 {
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
-		};
-
-		sdldo_reg: sdldo {
-			regulator-min-microvolt = <3000000>;
-			regulator-max-microvolt = <3000000>;
-		};
-
-		sdxldo_reg: sdxldo {
-			regulator-min-microvolt = <2700000>;
-			regulator-max-microvolt = <3300000>;
-		};
-
-		usbldo_reg: usbldo {
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
-		};
-
-		iosr1_reg: iosr1 {
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <1800000>;
-			regulator-always-on;
-		};
-	};
-};
--- a/arch/arm/boot/dts/broadcom/bcm2837-rpi-2-b.dts
+++ b/arch/arm/boot/dts/broadcom/bcm2837-rpi-2-b.dts
@ -0,0 +1,130 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+#include "bcm2837.dtsi"
+#include "bcm2836-rpi.dtsi"
+#include "bcm283x-rpi-led-deprecated.dtsi"
+#include "bcm283x-rpi-smsc9514.dtsi"
+#include "bcm283x-rpi-usb-host.dtsi"
+
+/ {
+	compatible = "raspberrypi,2-model-b-rev2", "brcm,bcm2837";
+	model = "Raspberry Pi 2 Model B rev 1.2";
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0 0x40000000>;
+	};
+};
+
+&gpio {
+	/*
+	 * Taken from rpi_SCH_2b_1p2_reduced.pdf and
+	 * the official GPU firmware DT blob.
+	 *
+	 * Legend:
+	 * "FOO" = GPIO line named "FOO" on the schematic
+	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
+	 */
+	gpio-line-names = "ID_SDA",
+			  "ID_SCL",
+			  "GPIO2",
+			  "GPIO3",
+			  "GPIO4",
+			  "GPIO5",
+			  "GPIO6",
+			  "GPIO7",
+			  "GPIO8",
+			  "GPIO9",
+			  "GPIO10",
+			  "GPIO11",
+			  "GPIO12",
+			  "GPIO13",
+			  "GPIO14",
+			  "GPIO15",
+			  "GPIO16",
+			  "GPIO17",
+			  "GPIO18",
+			  "GPIO19",
+			  "GPIO20",
+			  "GPIO21",
+			  "GPIO22",
+			  "GPIO23",
+			  "GPIO24",
+			  "GPIO25",
+			  "GPIO26",
+			  "GPIO27",
+			  "SDA0",
+			  "SCL0",
+			  "", /* GPIO30 */
+			  "LAN_RUN",
+			  "CAM_GPIO1",
+			  "", /* GPIO33 */
+			  "", /* GPIO34 */
+			  "PWR_LOW_N",
+			  "", /* GPIO36 */
+			  "", /* GPIO37 */
+			  "USB_LIMIT",
+			  "", /* GPIO39 */
+			  "PWM0_OUT",
+			  "CAM_GPIO0",
+			  "SMPS_SCL",
+			  "SMPS_SDA",
+			  "ETH_CLK",
+			  "PWM1_OUT",
+			  "HDMI_HPD_N",
+			  "STATUS_LED",
+			  /* Used by SD Card */
+			  "SD_CLK_R",
+			  "SD_CMD_R",
+			  "SD_DATA0_R",
+			  "SD_DATA1_R",
+			  "SD_DATA2_R",
+			  "SD_DATA3_R";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&gpioout &alt0 &i2s_alt0>;
+
+	/* I2S interface */
+	i2s_alt0: i2s_alt0 {
+		brcm,pins = <18 19 20 21>;
+		brcm,function = <BCM2835_FSEL_ALT0>;
+	};
+};
+
+&hdmi {
+	hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
+	power-domains = <&power RPI_POWER_DOMAIN_HDMI>;
+	status = "okay";
+};
+
+&led_act {
+	gpios = <&gpio 47 GPIO_ACTIVE_HIGH>;
+};
+
+&leds {
+	led-pwr {
+		label = "PWR";
+		gpios = <&gpio 35 GPIO_ACTIVE_HIGH>;
+		default-state = "keep";
+		linux,default-trigger = "default-on";
+	};
+};
+
+&pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio45>;
+	status = "okay";
+};
+
+&sdhost {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdhost_gpio48>;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_gpio14>;
+	status = "okay";
+};
--- a/arch/arm/boot/dts/broadcom/bcm59056.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm59056.dtsi
@ -1,91 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
-* Copyright 2014 Linaro Limited
-* Author: Matt Porter <mporter@linaro.org>
-*/
-
-&pmu {
-	compatible = "brcm,bcm59056";
-	regulators {
-		rfldo_reg: rfldo {
-		};
-
-		camldo1_reg: camldo1 {
-		};
-
-		camldo2_reg: camldo2 {
-		};
-
-		simldo1_reg: simldo1 {
-		};
-
-		simldo2_reg: simldo2 {
-		};
-
-		sdldo_reg: sdldo {
-		};
-
-		sdxldo_reg: sdxldo {
-		};
-
-		mmcldo1_reg: mmcldo1 {
-		};
-
-		mmcldo2_reg: mmcldo2 {
-		};
-
-		audldo_reg: audldo {
-		};
-
-		micldo_reg: micldo {
-		};
-
-		usbldo_reg: usbldo {
-		};
-
-		vibldo_reg: vibldo {
-		};
-
-		csr_reg: csr {
-		};
-
-		iosr1_reg: iosr1 {
-		};
-
-		iosr2_reg: iosr2 {
-		};
-
-		msr_reg: msr {
-		};
-
-		sdsr1_reg: sdsr1 {
-		};
-
-		sdsr2_reg: sdsr2 {
-		};
-
-		vsr_reg: vsr {
-		};
-
-		gpldo1_reg: gpldo1 {
-		};
-
-		gpldo2_reg: gpldo2 {
-		};
-
-		gpldo3_reg: gpldo3 {
-		};
-
-		gpldo4_reg: gpldo4 {
-		};
-
-		gpldo5_reg: gpldo5 {
-		};
-
-		gpldo6_reg: gpldo6 {
-		};
-
-		vbus_reg: vbus {
-		};
-	};
-};
--- a/arch/arm/boot/dts/intel/socfpga/Makefile
+++ b/arch/arm/boot/dts/intel/socfpga/Makefile
@ -10,6 +10,7 @@ dtb-$(CONFIG_ARCH_INTEL_SOCFPGA) += \
 	socfpga_cyclone5_mcvevk.dtb \
 	socfpga_cyclone5_socdk.dtb \
 	socfpga_cyclone5_de0_nano_soc.dtb \
+	socfpga_cyclone5_de10nano.dtb \
 	socfpga_cyclone5_sockit.dtb \
 	socfpga_cyclone5_socrates.dtb \
 	socfpga_cyclone5_sodia.dtb \
--- a/arch/arm/boot/dts/intel/socfpga/socfpga_cyclone5_de10nano.dts
+++ b/arch/arm/boot/dts/intel/socfpga/socfpga_cyclone5_de10nano.dts
@ -0,0 +1,95 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2017, Intel Corporation
+ *
+ * based on socfpga_cyclone5_de0_nano_soc.dts
+ */
+/dts-v1/;
+
+#include "socfpga_cyclone5.dtsi"
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "Terasic DE10-Nano";
+	compatible = "terasic,de10-nano", "altr,socfpga-cyclone5", "altr,socfpga";
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		/* 1 GiB */
+		device_type = "memory";
+		reg = <0x0 0x40000000>;
+	};
+
+	soc {
+		fpga: bus@ff200000 {
+			compatible = "simple-bus";
+			reg = <0xff200000 0x00200000>;
+			ranges = <0x00000000 0xff200000 0x00200000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			/*
+			 * Here the devices will appear if an FPGA image is
+			 * loaded. Their description is expected to be added
+			 * using a device tree overlay that matches the image.
+			 */
+		};
+	};
+};
+
+&gmac1 {
+	/* Uses a KSZ9031RNX phy */
+	phy-mode = "rgmii-id";
+	rxd0-skew-ps = <420>;
+	rxd1-skew-ps = <420>;
+	rxd2-skew-ps = <420>;
+	rxd3-skew-ps = <420>;
+	txen-skew-ps = <0>;
+	rxdv-skew-ps = <420>;
+	status = "okay";
+};
+
+&gpio0 {
+	status = "okay";
+};
+
+&gpio1 {
+	status = "okay";
+};
+
+&gpio2 {
+	status = "okay";
+};
+
+&i2c0 {
+	clock-frequency = <100000>;
+	status = "okay";
+
+	accelerometer@53 {
+		compatible = "adi,adxl345";
+		reg = <0x53>;
+		/* HPS_GSENSOR_INT is routed to UART0_RX/CAN0_RX/SPIM0_SS1/HPS_GPIO61 */
+		interrupt-parent = <&portc>;
+		interrupts = <3 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "INT1";
+	};
+};
+
+&mmc0 {
+	/* micro SD card socket J11 */
+	status = "okay";
+};
+
+&uart0 {
+	/*
+	 * Accessible via USB (FT232R) on Mini-USB plug J4
+	 * RX = TRACE_D0/SPIS0_CLK/UART0_RX/HPS_GPIO49
+	 * TX = TRACE_D1/SPIS0_MOSI/UART0_TX/HPS_GPIO50
+	 * no handshaking lines
+	 */
+	clock-frequency = <100000000>;
+};
--- a/arch/arm/boot/dts/marvell/kirkwood-db.dtsi
+++ b/arch/arm/boot/dts/marvell/kirkwood-db.dtsi
@ -39,7 +39,7 @@
 			status = "okay";
 		};

-		ehci@50000 {
+		usb@50000 {
 			status = "okay";
 		};

--- a/arch/arm/boot/dts/marvell/kirkwood-dir665.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-dir665.dts
@ -129,7 +129,7 @@
 			status = "okay";
 		};

-		ehci@50000 {
+		usb@50000 {
 			status = "okay";
 		};
 	};
--- a/arch/arm/boot/dts/marvell/kirkwood-mv88f6281gtw-ge.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-mv88f6281gtw-ge.dts
@ -63,7 +63,7 @@
 			status = "okay";
 		};

-		ehci@50000 {
+		usb@50000 {
 			status = "okay";
 		};
 	};
--- a/arch/arm/boot/dts/marvell/kirkwood.dtsi
+++ b/arch/arm/boot/dts/marvell/kirkwood.dtsi
@ -263,7 +263,7 @@
 			status = "okay";
 		};

-		usb0: ehci@50000 {
+		usb0: usb@50000 {
 			compatible = "marvell,orion-ehci";
 			reg = <0x50000 0x1000>;
 			interrupts = <19>;
--- a/arch/arm/boot/dts/marvell/orion5x.dtsi
+++ b/arch/arm/boot/dts/marvell/orion5x.dtsi
@ -146,7 +146,7 @@
 				status = "okay";
 			};

-			ehci0: ehci@50000 {
+			ehci0: usb@50000 {
 				compatible = "marvell,orion-ehci";
 				reg = <0x50000 0x1000>;
 				interrupts = <17>;
@ -218,7 +218,7 @@
 				status = "okay";
 			};

-			ehci1: ehci@a0000 {
+			ehci1: usb@a0000 {
 				compatible = "marvell,orion-ehci";
 				reg = <0xa0000 0x1000>;
 				interrupts = <12>;
--- a/arch/arm/boot/dts/mediatek/mt2701-evb.dts
+++ b/arch/arm/boot/dts/mediatek/mt2701-evb.dts
@ -50,6 +50,7 @@

 	bt_sco_codec:bt_sco_codec {
 		compatible = "linux,bt-sco";
+		#sound-dai-cells = <0>;
 	};

 	backlight_lcd: backlight_lcd {
--- a/arch/arm/boot/dts/microchip/at91-sama7d65_curiosity.dts
+++ b/arch/arm/boot/dts/microchip/at91-sama7d65_curiosity.dts
@ -30,6 +30,15 @@
 		device_type = "memory";
 		reg = <0x60000000 0x40000000>;
 	};
+
+	reg_5v: regulator-5v {
+		compatible = "regulator-fixed";
+		regulator-name = "5V_MAIN";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+
 };

 &dma0 {
@ -60,6 +69,26 @@
 	status = "okay";
 };

+&gmac0 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gmac0_default
+		     &pinctrl_gmac0_mdio_default
+		     &pinctrl_gmac0_txck_default
+		     &pinctrl_gmac0_phy_irq>;
+	phy-mode = "rgmii-id";
+	nvmem-cells = <&eeprom0_eui48>;
+	nvmem-cell-names = "mac-address";
+	status = "okay";
+
+	ethernet-phy@7 {
+		reg = <0x7>;
+		interrupt-parent = <&pioa>;
+		interrupts = <PIN_PC1 IRQ_TYPE_LEVEL_LOW>;
+	};
+};
+
 &i2c10 {
 	dmas = <0>, <0>;
 	i2c-analog-filter;
@ -99,6 +128,149 @@
 			label = "VDDCPU";
 		};
 	};
+
+	pmic@5b {
+		compatible = "microchip,mcp16502";
+		reg = <0x5b>;
+		lvin-supply = <&reg_5v>;
+		pvin1-supply = <&reg_5v>;
+		pvin2-supply = <&reg_5v>;
+		pvin3-supply = <&reg_5v>;
+		pvin4-supply = <&reg_5v>;
+		status = "okay";
+
+		regulators {
+			vdd_3v3: VDD_IO {
+				regulator-name = "VDD_IO";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-initial-mode = <2>;
+				regulator-allowed-modes = <2>, <4>;
+				regulator-always-on;
+
+				regulator-state-standby {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3300000>;
+					regulator-mode = <4>;
+				};
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+					regulator-mode = <4>;
+				};
+			};
+
+			vddioddr: VDD_DDR {
+				regulator-name = "VDD_DDR";
+				regulator-min-microvolt = <1350000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-initial-mode = <2>;
+				regulator-allowed-modes = <2>, <4>;
+				regulator-always-on;
+
+				regulator-state-standby {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1350000>;
+					regulator-mode = <4>;
+				};
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1350000>;
+					regulator-mode = <4>;
+				};
+			};
+
+			vddcore: VDD_CORE {
+				regulator-name = "VDD_CORE";
+				regulator-min-microvolt = <1050000>;
+				regulator-max-microvolt = <1050000>;
+				regulator-initial-mode = <2>;
+				regulator-allowed-modes = <2>, <4>;
+				regulator-always-on;
+
+				regulator-state-standby {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1050000>;
+					regulator-mode = <4>;
+				};
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+					regulator-mode = <4>;
+				};
+			};
+
+			vddcpu: VDD_OTHER {
+				regulator-name = "VDD_OTHER";
+				regulator-min-microvolt = <1050000>;
+				regulator-max-microvolt = <1250000>;
+				regulator-initial-mode = <2>;
+				regulator-allowed-modes = <2>, <4>;
+				regulator-ramp-delay = <3125>;
+				regulator-always-on;
+
+				regulator-state-standby {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1050000>;
+					regulator-mode = <4>;
+				};
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+					regulator-mode = <4>;
+				};
+			};
+
+			vldo1: LDO1 {
+				regulator-name = "LDO1";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+
+				regulator-state-standby {
+					regulator-suspend-microvolt = <1800000>;
+					regulator-on-in-suspend;
+				};
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vldo2: LDO2 {
+				regulator-name = "LDO2";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <3700000>;
+
+				regulator-state-standby {
+					regulator-on-in-suspend;
+				};
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+		};
+	};
+
+	eeprom0: eeprom@51 {
+		compatible = "microchip,24aa025e48";
+		reg = <0x51>;
+		size = <256>;
+		pagesize = <16>;
+		vcc-supply = <&vdd_3v3>;
+
+		nvmem-layout {
+			compatible = "fixed-layout";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			eeprom0_eui48: eui48@fa {
+				reg = <0xfa 0x6>;
+			};
+		};
+	};
 };

 &main_xtal {
@ -106,6 +278,39 @@
 };

 &pioa {
+	pinctrl_gmac0_default: gmac0-default {
+		pinmux = <PIN_PA26__G0_TX0>,
+			 <PIN_PA27__G0_TX1>,
+			 <PIN_PB4__G0_TX2>,
+			 <PIN_PB5__G0_TX3>,
+			 <PIN_PA29__G0_RX0>,
+			 <PIN_PA30__G0_RX1>,
+			 <PIN_PB2__G0_RX2>,
+			 <PIN_PB6__G0_RX3>,
+			 <PIN_PA25__G0_TXCTL>,
+			 <PIN_PB3__G0_RXCK>,
+			 <PIN_PA28__G0_RXCTL>;
+		slew-rate = <0>;
+		bias-disable;
+	};
+
+	pinctrl_gmac0_mdio_default: gmac0-mdio-default {
+		pinmux = <PIN_PA31__G0_MDC>,
+			 <PIN_PB0__G0_MDIO>;
+		bias-disable;
+	};
+
+	pinctrl_gmac0_phy_irq: gmac0-phy-irq {
+		pinmux = <PIN_PC1__GPIO>;
+		bias-disable;
+	};
+
+	pinctrl_gmac0_txck_default: gmac0-txck-default {
+		pinmux = <PIN_PB1__G0_REFCK>;
+		slew-rate = <0>;
+		bias-pull-up;
+	};
+
 	pinctrl_i2c10_default: i2c10-default{
 		pinmux = <PIN_PB19__FLEXCOM10_IO1>,
 			 <PIN_PB20__FLEXCOM10_IO0>;
@ -141,6 +346,10 @@
 	};
 };

+&rtt {
+	atmel,rtt-rtc-time-reg = <&gpbr 0x0>;
+};
+
 &sdmmc1 {
 	bus-width = <4>;
 	pinctrl-names = "default";
--- a/arch/arm/boot/dts/microchip/at91-sama7g54_curiosity.dts
+++ b/arch/arm/boot/dts/microchip/at91-sama7g54_curiosity.dts
@ -369,6 +369,38 @@
 		spi-tx-bus-width = <4>;
 		spi-rx-bus-width = <4>;
 		m25p,fast-read;
+		label = "at91-qspi";
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			at91bootstrap@0 {
+				label = "qspi1: at91bootstrap";
+				reg = <0x0 0x40000>;
+			};
+
+			bootloader@40000 {
+				label = "qspi1: u-boot";
+				reg = <0x40000 0x100000>;
+			};
+
+			bootloaderenv@140000 {
+				label = "qspi1: u-boot env";
+				reg = <0x140000 0x40000>;
+			};
+
+			dtb@180000 {
+				label = "qspi1: device tree";
+				reg = <0x180000 0x80000>;
+			};
+
+			kernel@200000 {
+				label = "qspi1: kernel";
+				reg = <0x200000 0x600000>;
+			};
+		};
 	};
 };

--- a/arch/arm/boot/dts/microchip/at91sam9263ek.dts
+++ b/arch/arm/boot/dts/microchip/at91sam9263ek.dts
@ -152,7 +152,7 @@
 				nand@3 {
 					reg = <0x3 0x0 0x800000>;
 					rb-gpios = <&pioA 22 GPIO_ACTIVE_HIGH>;
-					cs-gpios = <&pioA 15 GPIO_ACTIVE_HIGH>;
+					cs-gpios = <&pioD 15 GPIO_ACTIVE_HIGH>;
 					nand-bus-width = <8>;
 					nand-ecc-mode = "soft";
 					nand-on-flash-bbt;
--- a/arch/arm/boot/dts/microchip/sama7d65.dtsi
+++ b/arch/arm/boot/dts/microchip/sama7d65.dtsi
@ -47,12 +47,37 @@
 		};
 	};

+	ns_sram: sram@100000 {
+		compatible = "mmio-sram";
+		reg = <0x100000 0x20000>;
+		ranges;
+		#address-cells = <1>;
+		#size-cells = <1>;
+	};
+
 	soc {
 		compatible = "simple-bus";
 		ranges;
 		#address-cells = <1>;
 		#size-cells = <1>;

+		securam: sram@e0000800 {
+			compatible = "microchip,sama7d65-securam", "atmel,sama5d2-securam", "mmio-sram";
+			reg = <0xe0000800 0x4000>;
+			ranges = <0 0xe0000800 0x4000>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 17>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			no-memory-wc;
+		};
+
+		secumod: security-module@e0004000 {
+			compatible = "microchip,sama7d65-secumod", "atmel,sama5d2-secumod", "syscon";
+			reg = <0xe0004000 0x4000>;
+			gpio-controller;
+			#gpio-cells = <2>;
+		};
+
 		sfrbu: sfr@e0008000 {
 			compatible ="microchip,sama7d65-sfrbu", "atmel,sama5d2-sfrbu", "syscon";
 			reg = <0xe0008000 0x20>;
@ -107,6 +132,13 @@
 			status = "disabled";
 		};

+		rtt: rtc@e001d300 {
+			compatible = "microchip,sama7d65-rtt", "atmel,at91sam9260-rtt";
+			reg = <0xe001d300 0x30>;
+			interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk32k 0>;
+		};
+
 		clk32k: clock-controller@e001d500 {
 			compatible = "microchip,sama7d65-sckc", "microchip,sam9x60-sckc";
 			reg = <0xe001d500 0x4>;
@ -114,6 +146,11 @@
 			#clock-cells = <1>;
 		};

+		gpbr: syscon@e001d700 {
+			compatible = "microchip,sama7d65-gpbr", "syscon";
+			reg = <0xe001d700 0x48>;
+		};
+
 		rtc: rtc@e001d800 {
 			compatible = "microchip,sama7d65-rtc", "microchip,sam9x60-rtc";
 			reg = <0xe001d800 0x30>;
@ -169,6 +206,38 @@
 			status = "disabled";
 		};

+		gmac0: ethernet@e1618000 {
+			compatible = "microchip,sama7d65-gem", "microchip,sama7g5-gem";
+			reg = <0xe1618000 0x2000>;
+			interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 46>, <&pmc PMC_TYPE_PERIPHERAL 46>, <&pmc PMC_TYPE_GCK 46>, <&pmc PMC_TYPE_GCK 49>;
+			clock-names = "pclk", "hclk", "tx_clk", "tsu_clk";
+			assigned-clocks = <&pmc PMC_TYPE_GCK 46>, <&pmc PMC_TYPE_GCK 49>;
+			assigned-clock-rates = <125000000>, <200000000>;
+			status = "disabled";
+		};
+
+		gmac1: ethernet@e161c000 {
+			compatible = "microchip,sama7d65-gem", "microchip,sama7g5-gem";
+			reg = <0xe161c000 0x2000>;
+			interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 151 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 152 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 47>, <&pmc PMC_TYPE_PERIPHERAL 47>,<&pmc PMC_TYPE_GCK 47>, <&pmc PMC_TYPE_GCK 50>;
+			clock-names = "pclk", "hclk", "tx_clk", "tsu_clk";
+			assigned-clocks = <&pmc PMC_TYPE_GCK 47>, <&pmc PMC_TYPE_GCK 50>;
+			assigned-clock-rates = <125000000>, <200000000>;
+			status = "disabled";
+		};
+
 		pit64b0: timer@e1800000 {
 			compatible = "microchip,sama7d65-pit64b", "microchip,sam9x60-pit64b";
 			reg = <0xe1800000 0x100>;
@ -185,6 +254,199 @@
 			clock-names = "pclk", "gclk";
 		};

+		flx0: flexcom@e1820000 {
+			compatible = "microchip,sama7d65-flexcom", "atmel,sama5d2-flexcom";
+			reg = <0xe1820000 0x200>;
+			ranges = <0x0 0xe1820000 0x800>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 34>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			status = "disabled";
+
+			uart0: serial@200 {
+				compatible = "microchip,sama7d65-usart", "atmel,at91sam9260-usart";
+				reg = <0x200 0x200>;
+				interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 34>;
+				clock-names = "usart";
+				dmas = <&dma1 AT91_XDMAC_DT_PERID(6)>,
+				       <&dma1 AT91_XDMAC_DT_PERID(5)>;
+				dma-names = "tx", "rx";
+				atmel,use-dma-rx;
+				atmel,use-dma-tx;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
+				status = "disabled";
+			};
+
+			i2c0: i2c@600 {
+				compatible = "microchip,sama7d65-i2c", "microchip,sam9x60-i2c";
+				reg = <0x600 0x200>;
+				interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 34>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				atmel,fifo-size = <32>;
+				dmas = <&dma0 AT91_XDMAC_DT_PERID(6)>,
+				       <&dma0 AT91_XDMAC_DT_PERID(5)>;
+				dma-names = "tx", "rx";
+				status = "disabled";
+			};
+		};
+
+		flx1: flexcom@e1824000 {
+			compatible = "microchip,sama7d65-flexcom", "atmel,sama5d2-flexcom";
+			reg = <0xe1824000 0x200>;
+			ranges = <0x0 0xe1824000 0x800>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 35>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			status = "disabled";
+
+			spi1: spi@400 {
+				compatible = "microchip,sama7d65-spi", "atmel,at91rm9200-spi";
+				reg = <0x400 0x200>;
+				interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 35>;
+				clock-names = "spi_clk";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				dmas = <&dma0 AT91_XDMAC_DT_PERID(8)>,
+				       <&dma0 AT91_XDMAC_DT_PERID(7)>;
+				dma-names = "tx", "rx";
+				atmel,fifo-size = <32>;
+				status = "disabled";
+			};
+
+			i2c1: i2c@600 {
+				compatible = "microchip,sama7d65-i2c", "microchip,sam9x60-i2c";
+				reg = <0x600 0x200>;
+				interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 35>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				dmas = <&dma0 AT91_XDMAC_DT_PERID(8)>,
+				       <&dma0 AT91_XDMAC_DT_PERID(7)>;
+				dma-names = "tx", "rx";
+				atmel,fifo-size = <32>;
+				status = "disabled";
+			};
+		};
+
+		flx2: flexcom@e1828000 {
+			compatible = "microchip,sama7d65-flexcom", "atmel,sama5d2-flexcom";
+			reg = <0xe1828000 0x200>;
+			ranges = <0x0 0xe1828000 0x800>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 36>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			status = "disabled";
+
+			uart2: serial@200 {
+				compatible = "microchip,sama7d65-usart", "atmel,at91sam9260-usart";
+				reg = <0x200 0x200>;
+				interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 36>;
+				clock-names = "usart";
+				dmas = <&dma1 AT91_XDMAC_DT_PERID(10)>,
+				       <&dma1 AT91_XDMAC_DT_PERID(9)>;
+				dma-names = "tx", "rx";
+				atmel,use-dma-rx;
+				atmel,use-dma-tx;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
+				status = "disabled";
+			};
+		};
+
+		flx3: flexcom@e182c000 {
+			compatible = "microchip,sama7d65-flexcom", "atmel,sama5d2-flexcom";
+			reg = <0xe182c000 0x200>;
+			ranges = <0x0 0xe182c000 0x800>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 37>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			status = "disabled";
+
+			i2c3: i2c@600 {
+				compatible = "microchip,sama7d65-i2c", "microchip,sam9x60-i2c";
+				reg = <0x600 0x200>;
+				interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 37>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				dmas = <&dma0 AT91_XDMAC_DT_PERID(12)>,
+				       <&dma0 AT91_XDMAC_DT_PERID(11)>;
+				dma-names = "tx", "rx";
+				atmel,fifo-size = <32>;
+				status = "disabled";
+			};
+
+		};
+
+		flx4: flexcom@e2018000 {
+			compatible = "microchip,sama7d65-flexcom", "atmel,sama5d2-flexcom";
+			reg = <0xe2018000 0x200>;
+			ranges = <0x0 0xe2018000 0x800>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 38>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			status = "disabled";
+
+			uart4: serial@200 {
+				compatible = "microchip,sama7d65-usart", "atmel,at91sam9260-usart";
+				reg = <0x200 0x200>;
+				interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 38>;
+				clock-names = "usart";
+				dmas = <&dma1 AT91_XDMAC_DT_PERID(14)>,
+				       <&dma1 AT91_XDMAC_DT_PERID(13)>;
+				dma-names = "tx", "rx";
+				atmel,use-dma-rx;
+				atmel,use-dma-tx;
+				atmel,fifo-size = <16>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
+				status = "disabled";
+			};
+
+			spi4: spi@400 {
+				compatible = "microchip,sama7d65-spi", "atmel,at91rm9200-spi";
+				reg = <0x400 0x200>;
+				interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 38>;
+				clock-names = "spi_clk";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				dmas = <&dma0 AT91_XDMAC_DT_PERID(14)>,
+				       <&dma0 AT91_XDMAC_DT_PERID(13)>;
+				dma-names = "tx", "rx";
+				atmel,fifo-size = <32>;
+				status = "disabled";
+			};
+		};
+
+		flx5: flexcom@e201c000 {
+			compatible = "microchip,sama7d65-flexcom", "atmel,sama5d2-flexcom";
+			reg = <0xe201c000 0x200>;
+			ranges = <0x0 0xe201c000 0x800>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 39>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			status = "disabled";
+
+			i2c5: i2c@600 {
+				compatible = "microchip,sama7d65-i2c", "microchip,sam9x60-i2c";
+				reg = <0x600 0x200>;
+				interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 39>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				dmas = <&dma0 AT91_XDMAC_DT_PERID(16)>,
+				       <&dma0 AT91_XDMAC_DT_PERID(15)>;
+				dma-names = "tx", "rx";
+				atmel,fifo-size = <32>;
+				status = "disabled";
+			};
+		};
+
 		flx6: flexcom@e2020000 {
 			compatible = "microchip,sama7d65-flexcom", "atmel,sama5d2-flexcom";
 			reg = <0xe2020000 0x200>;
@ -206,6 +468,80 @@
 			};
 		};

+		flx7: flexcom@e2024000 {
+			compatible = "microchip,sama7d65-flexcom", "atmel,sama5d2-flexcom";
+			reg = <0xe2024000 0x200>;
+			ranges = <0x0 0xe2024000 0x800>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 41>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			status = "disabled";
+
+			uart7: serial@200 {
+				compatible = "microchip,sama7d65-usart", "atmel,at91sam9260-usart";
+				reg = <0x200 0x200>;
+				interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 41>;
+				clock-names = "usart";
+				dmas = <&dma1 AT91_XDMAC_DT_PERID(20)>,
+				       <&dma1 AT91_XDMAC_DT_PERID(19)>;
+				dma-names = "tx", "rx";
+				atmel,use-dma-rx;
+				atmel,use-dma-tx;
+				atmel,fifo-size = <16>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
+				status = "disabled";
+			};
+		};
+
+		flx8: flexcom@e281c000 {
+			compatible = "microchip,sama7d65-flexcom", "atmel,sama5d2-flexcom";
+			reg = <0xe281c000 0x200>;
+			ranges = <0x0 0xe281c000 0x800>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 42>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			status = "disabled";
+
+			i2c8: i2c@600 {
+				compatible = "microchip,sama7d65-i2c", "microchip,sam9x60-i2c";
+				reg = <0x600 0x200>;
+				interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 42>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				dmas = <&dma0 AT91_XDMAC_DT_PERID(22)>,
+				       <&dma0 AT91_XDMAC_DT_PERID(21)>;
+				dma-names = "tx", "rx";
+				atmel,fifo-size = <32>;
+				status = "disabled";
+			};
+		};
+
+		flx9: flexcom@e2820000 {
+			compatible = "microchip,sama7d65-flexcom", "atmel,sama5d2-flexcom";
+			reg = <0xe2820000 0x200>;
+			ranges = <0x0 0xe281c000 0x800>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 43>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			status = "disabled";
+
+			i2c9: i2c@600 {
+				compatible = "microchip,sama7d65-i2c", "microchip,sam9x60-i2c";
+				reg = <0x600 0x200>;
+				interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 43>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				dmas = <&dma0 AT91_XDMAC_DT_PERID(24)>,
+				       <&dma0 AT91_XDMAC_DT_PERID(23)>;
+				dma-names = "tx", "rx";
+				atmel,fifo-size = <32>;
+				status = "disabled";
+			};
+		};
+
 		flx10: flexcom@e2824000 {
 			compatible = "microchip,sama7d65-flexcom", "atmel,sama5d2-flexcom";
 			reg = <0xe2824000 0x200>;
@ -227,6 +563,16 @@
 			};
 		};

+		uddrc: uddrc@e3800000 {
+			compatible = "microchip,sama7d65-uddrc", "microchip,sama7g5-uddrc";
+			reg = <0xe3800000 0x4000>;
+		};
+
+		ddr3phy: ddr3phy@e3804000 {
+			compatible = "microchip,sama7d65-ddr3phy", "microchip,sama7g5-ddr3phy";
+			reg = <0xe3804000 0x1000>;
+		};
+
 		gic: interrupt-controller@e8c11000 {
 			compatible = "arm,cortex-a7-gic";
 			reg = <0xe8c11000 0x1000>,
--- a/arch/arm/boot/dts/microchip/tny_a9263.dts
+++ b/arch/arm/boot/dts/microchip/tny_a9263.dts
@ -64,7 +64,7 @@
 				nand@3 {
 					reg = <0x3 0x0 0x800000>;
 					rb-gpios = <&pioA 22 GPIO_ACTIVE_HIGH>;
-					cs-gpios = <&pioA 15 GPIO_ACTIVE_HIGH>;
+					cs-gpios = <&pioD 15 GPIO_ACTIVE_HIGH>;
 					nand-bus-width = <8>;
 					nand-ecc-mode = "soft";
 					nand-on-flash-bbt;
--- a/arch/arm/boot/dts/microchip/usb_a9260.dts
+++ b/arch/arm/boot/dts/microchip/usb_a9260.dts
@ -12,14 +12,6 @@
 	model = "Calao USB A9260";
 	compatible = "calao,usb-a9260", "atmel,at91sam9260", "atmel,at91sam9";

-	chosen {
-		bootargs = "mem=64M console=ttyS0,115200 root=/dev/mtdblock5 rw rootfstype=ubifs";
-	};
-
-	memory@20000000 {
-		reg = <0x20000000 0x4000000>;
-	};
-
 	ahb {
 		apb {
 			shdwc: poweroff@fffffd10 {
--- a/arch/arm/boot/dts/microchip/usb_a9260_common.dtsi
+++ b/arch/arm/boot/dts/microchip/usb_a9260_common.dtsi
@ -6,6 +6,11 @@
 */

 / {
+	chosen {
+		bootargs = "mem=64M root=/dev/mtdblock5 rw rootfstype=ubifs";
+		stdout-path = "serial0:115200n8";
+	};
+
 	clocks {
 		slow_xtal {
 			clock-frequency = <32768>;
@ -16,6 +21,10 @@
 		};
 	};

+	memory@20000000 {
+		reg = <0x20000000 0x4000000>;
+	};
+
 	ahb {
 		apb {
 			dbgu: serial@fffff200 {
--- a/arch/arm/boot/dts/microchip/usb_a9263.dts
+++ b/arch/arm/boot/dts/microchip/usb_a9263.dts
@ -58,7 +58,7 @@
 			};

 			spi0: spi@fffa4000 {
-				cs-gpios = <&pioB 15 GPIO_ACTIVE_HIGH>;
+				cs-gpios = <&pioA 5 GPIO_ACTIVE_LOW>;
 				status = "okay";
 				flash@0 {
 					compatible = "atmel,at45", "atmel,dataflash";
@ -84,7 +84,7 @@
 				nand@3 {
 					reg = <0x3 0x0 0x800000>;
 					rb-gpios = <&pioA 22 GPIO_ACTIVE_HIGH>;
-					cs-gpios = <&pioA 15 GPIO_ACTIVE_HIGH>;
+					cs-gpios = <&pioD 15 GPIO_ACTIVE_HIGH>;
 					nand-bus-width = <8>;
 					nand-ecc-mode = "soft";
 					nand-on-flash-bbt;
--- a/arch/arm/boot/dts/microchip/usb_a9g20.dts
+++ b/arch/arm/boot/dts/microchip/usb_a9g20.dts
@ -5,9 +5,24 @@
 *  Copyright (C) 2011 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
 */
 /dts-v1/;
-#include "usb_a9g20_common.dtsi"
+#include "at91sam9g20.dtsi"
+#include "usb_a9260_common.dtsi"

 / {
 	model = "Calao USB A9G20";
 	compatible = "calao,usb-a9g20", "atmel,at91sam9g20", "atmel,at91sam9";
 };
+
+&spi0 {
+	cs-gpios = <&pioC 11 GPIO_ACTIVE_LOW>;
+	status = "okay";
+	/* TODO: Some revisions might have a dataflash here instead of an EEPROM */
+	eeprom@0 {
+		compatible = "st,m95640", "atmel,at25";
+		reg = <0>;
+		spi-max-frequency = <2000000>;
+		size = <8192>;
+		pagesize = <32>;
+		address-width = <16>;
+	};
+};
--- a/arch/arm/boot/dts/microchip/usb_a9g20_common.dtsi
+++ b/arch/arm/boot/dts/microchip/usb_a9g20_common.dtsi
@ -1,27 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * usb_a9g20.dts - Device Tree file for Calao USB A9G20 board
- *
- *  Copyright (C) 2011 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
- */
-
-#include "at91sam9g20.dtsi"
-#include "usb_a9260_common.dtsi"
-
-/ {
-	chosen {
-		bootargs = "mem=64M root=/dev/mtdblock5 rw rootfstype=ubifs";
-		stdout-path = "serial0:115200n8";
-	};
-
-	memory@20000000 {
-		reg = <0x20000000 0x4000000>;
-	};
-
-	i2c-gpio-0 {
-		rtc@56 {
-			compatible = "microcrystal,rv3029";
-			reg = <0x56>;
-		};
-	};
-};
--- a/arch/arm/boot/dts/microchip/usb_a9g20_lpw.dts
+++ b/arch/arm/boot/dts/microchip/usb_a9g20_lpw.dts
@ -5,7 +5,8 @@
 *  Copyright (C) 2013 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
 */
 /dts-v1/;
-#include "usb_a9g20_common.dtsi"
+#include "at91sam9g20.dtsi"
+#include "usb_a9260_common.dtsi"

 / {
 	model = "Calao USB A9G20 Low Power";
@ -27,4 +28,11 @@
 			};
 		};
 	};
+
+	i2c-gpio-0 {
+		rtc@56 {
+			compatible = "microcrystal,rv3029";
+			reg = <0x56>;
+		};
+	};
 };
--- a/arch/arm/boot/dts/nuvoton/nuvoton-common-npcm7xx.dtsi
+++ b/arch/arm/boot/dts/nuvoton/nuvoton-common-npcm7xx.dtsi
@ -99,6 +99,11 @@
 		};
 	};

+	udc0_phy: usb-phy {
+		compatible = "usb-nop-xceiv";
+		#phy-cells = <0>;
+	};
+
 	ahb {
 		#address-cells = <1>;
 		#size-cells = <1>;
@ -122,6 +127,13 @@
 			clocks = <&clk_refclk>, <&clk_sysbypck>, <&clk_mcbypck>;
 		};

+		mc: memory-controller@f0824000 {
+			compatible = "nuvoton,npcm750-memory-controller";
+			reg = <0xf0824000 0x1000>;
+			interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+		};
+
 		gmac0: eth@f0802000 {
 			device_type = "network";
 			compatible = "snps,dwmac";
@ -137,6 +149,29 @@
 			status = "disabled";
 		};

+		sdmmc: mmc@f0842000 {
+			compatible = "nuvoton,npcm750-sdhci";
+			status = "disabled";
+			reg = <0xf0842000 0x200>;
+			interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
+			clocks =  <&clk NPCM7XX_CLK_AHB>;
+			clock-names = "clk_mmc";
+			pinctrl-names = "default";
+			pinctrl-0 = <&mmc8_pins
+					&mmc_pins>;
+		};
+
+		sdhci: mmc@f0840000 {
+			compatible = "nuvoton,npcm750-sdhci";
+			status = "disabled";
+			reg = <0xf0840000 0x200>;
+			interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>;
+			clocks =  <&clk NPCM7XX_CLK_AHB>;
+			clock-names = "clk_sdhc";
+			pinctrl-names = "default";
+			pinctrl-0 = <&sd1_pins>;
+		};
+
 		ehci1: usb@f0806000 {
 			compatible = "nuvoton,npcm750-ehci";
 			reg = <0xf0806000 0x1000>;
@ -144,6 +179,13 @@
 			status = "disabled";
 		};

+		ohci1: usb@f0807000 {
+			compatible = "generic-ohci";
+			reg = <0xf0807000 0x1000>;
+			interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+		};
+
 		fiu0: spi@fb000000 {
 			compatible = "nuvoton,npcm750-fiu";
 			#address-cells = <1>;
@ -179,6 +221,72 @@
 			status = "disabled";
 		};

+		udc5: usb@f0835000 {
+			compatible = "nuvoton,npcm750-udc";
+			reg = <0xf0835000 0x1000
+			       0xfffd2800 0x800>;
+			interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk NPCM7XX_CLK_SU>;
+			clock-names = "clk_usb_bridge";
+			phys = <&udc0_phy>;
+			phy_type = "utmi_wide";
+			dr_mode = "peripheral";
+			status = "disabled";
+		};
+
+		udc6: usb@f0836000 {
+			compatible = "nuvoton,npcm750-udc";
+			reg = <0xf0836000 0x1000
+			       0xfffd3000 0x800>;
+			interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk NPCM7XX_CLK_SU>;
+			clock-names = "clk_usb_bridge";
+			phys = <&udc0_phy>;
+			phy_type = "utmi_wide";
+			dr_mode = "peripheral";
+			status = "disabled";
+		};
+
+		udc7: usb@f0837000 {
+			compatible = "nuvoton,npcm750-udc";
+			reg = <0xf0837000 0x1000
+			       0xfffd3800 0x800>;
+			interrupts = <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk NPCM7XX_CLK_SU>;
+			clock-names = "clk_usb_bridge";
+			phys = <&udc0_phy>;
+			phy_type = "utmi_wide";
+			dr_mode = "peripheral";
+			status = "disabled";
+		};
+
+		udc8: usb@f0838000 {
+			compatible = "nuvoton,npcm750-udc";
+			reg = <0xf0838000 0x1000
+			       0xfffd4000 0x800>;
+			interrupts = <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk NPCM7XX_CLK_SU>;
+			clock-names = "clk_usb_bridge";
+			phys = <&udc0_phy>;
+			phy_type = "utmi_wide";
+			dr_mode = "peripheral";
+			status = "disabled";
+		};
+
+		udc9: usb@f0839000 {
+			compatible = "nuvoton,npcm750-udc";
+			reg = <0xf0839000 0x1000
+			       0xfffd4800 0x800>;
+			interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk NPCM7XX_CLK_SU>;
+			clock-names = "clk_usb_bridge";
+			nuvoton,sysgcr = <&gcr>;
+			phys = <&udc0_phy>;
+			phy_type = "utmi_wide";
+			dr_mode = "peripheral";
+			status = "disabled";
+		};
+
 		apb {
 			#address-cells = <1>;
 			#size-cells = <1>;
--- a/arch/arm/boot/dts/nuvoton/nuvoton-npcm730-gbs.dts
+++ b/arch/arm/boot/dts/nuvoton/nuvoton-npcm730-gbs.dts
@ -1050,19 +1050,19 @@
 		"","","","SIO_POWER_GOOD","","","","";
 	};
 	gpio2: gpio@f0012000 {
-		bmc_usb_mux_oe_n {
+		bmc-usb-mux-oe-n-hog {
 			gpio-hog;
 			gpios = <25 GPIO_ACTIVE_HIGH>;
 			output-low;
 			line-name = "bmc-usb-mux-oe-n";
 		};
-		bmc_usb_mux_sel {
+		bmc-usb-mux-sel-hog {
 			gpio-hog;
 			gpios = <26 GPIO_ACTIVE_HIGH>;
 			output-low;
 			line-name = "bmc-usb-mux-sel";
 		};
-		bmc_usb2517_reset_n {
+		bmc-usb2517-reset-n-hog {
 			gpio-hog;
 			gpios = <27 GPIO_ACTIVE_LOW>;
 			output-low;
@ -1070,19 +1070,19 @@
 		};
 	};
 	gpio3: gpio@f0013000 {
-		assert_cpu0_reset {
+		assert-cpu0-reset-hog {
 			gpio-hog;
 			gpios = <14 GPIO_ACTIVE_HIGH>;
 			output-low;
 			line-name = "assert-cpu0-reset";
 		};
-		assert_pwrok_cpu0_n {
+		assert-pwrok-cpu0-n-hog {
 			gpio-hog;
 			gpios = <15 GPIO_ACTIVE_HIGH>;
 			output-low;
 			line-name = "assert-pwrok-cpu0-n";
 		};
-		assert_cpu0_prochot {
+		assert-cpu0-prochot-hog {
 			gpio-hog;
 			gpios = <16 GPIO_ACTIVE_HIGH>;
 			output-low;
--- a/arch/arm/boot/dts/nuvoton/nuvoton-npcm750-runbmc-olympus.dts
+++ b/arch/arm/boot/dts/nuvoton/nuvoton-npcm750-runbmc-olympus.dts
@ -427,91 +427,91 @@
 		gpio-controller;
 		#gpio-cells = <2>;
 		reset-gpios = <&gpio7 4 GPIO_ACTIVE_LOW>;
-		G1A_P0_0 {
+		g1a-p0-0-hog {
 			gpio-hog;
 			gpios = <0 0>;
 			output-high;
 			line-name = "TPM_BMC_ALERT_N";
 		};
-		G1A_P0_1 {
+		g1a-p0-1-hog {
 			gpio-hog;
 			gpios = <1 0>;
 			input;
 			line-name = "FM_BIOS_TOP_SWAP";
 		};
-		G1A_P0_2 {
+		g1a-p0-2-hog {
 			gpio-hog;
 			gpios = <2 0>;
 			input;
 			line-name = "FM_BIOS_PREFRB2_GOOD";
 		};
-		G1A_P0_3 {
+		g1a-p0-3-hog {
 			gpio-hog;
 			gpios = <3 0>;
 			input;
 			line-name = "BMC_SATAXPCIE_0TO3_SEL";
 		};
-		G1A_P0_4 {
+		g1a-p0-4-hog {
 			gpio-hog;
 			gpios = <4 0>;
 			input;
 			line-name = "BMC_SATAXPCIE_4TO7_SEL";
 		};
-		G1A_P0_5 {
+		g1a-p0-5-hog {
 			gpio-hog;
 			gpios = <5 0>;
 			output-low;
 			line-name = "FM_UV_ADR_TRIGGER_EN_N";
 		};
-		G1A_P0_6 {
+		g1a-p0-6-hog {
 			gpio-hog;
 			gpios = <6 0>;
 			input;
 			line-name = "RM_THROTTLE_EN_N";
 		};
-		G1A_P1_0 {
+		g1a-p1-0-hog {
 			gpio-hog;
 			gpios = <8 0>;
 			input;
 			line-name = "FM_BMC_TPM_PRES_N";
 		};
-		G1A_P1_1 {
+		g1a-p1-1-hog {
 			gpio-hog;
 			gpios = <9 0>;
 			input;
 			line-name = "FM_CPU0_SKTOCC_LVT3_N";
 		};
-		G1A_P1_2 {
+		g1a-p1-2-hog {
 			gpio-hog;
 			gpios = <10 0>;
 			input;
 			line-name = "FM_CPU1_SKTOCC_LVT3_N";
 		};
-		G1A_P1_3 {
+		g1a-p1-3-hog {
 			gpio-hog;
 			gpios = <11 0>;
 			input;
 			line-name = "PSU1_ALERT_N";
 		};
-		G1A_P1_4 {
+		g1a-p1-4-hog {
 			gpio-hog;
 			gpios = <12 0>;
 			input;
 			line-name = "PSU2_ALERT_N";
 		};
-		G1A_P1_5 {
+		g1a-p1-5-hog {
 			gpio-hog;
 			gpios = <13 0>;
 			input;
 			line-name = "H_CPU0_FAST_WAKE_LVT3_N";
 		};
-		G1A_P1_6 {
+		g1a-p1-6-hog {
 			gpio-hog;
 			gpios = <14 0>;
 			output-high;
 			line-name = "I2C_MUX1_RESET_N";
 		};
-		G1A_P1_7 {
+		g1a-p1-7-hog {
 			gpio-hog;
 			gpios = <15 0>;
 			input;
@ -524,91 +524,91 @@
 		reg = <0x75>;
 		gpio-controller;
 		#gpio-cells = <2>;
-		G1B_P0_0 {
+		g1b-p0-0-hog {
 			gpio-hog;
 			gpios = <0 0>;
 			input;
 			line-name = "PVDDQ_ABC_PINALERT_N";
 		};
-		G1B_P0_1 {
+		g1b-p0-1-hog {
 			gpio-hog;
 			gpios = <1 0>;
 			input;
 			line-name = "PVDDQ_DEF_PINALERT_N";
 		};
-		G1B_P0_2 {
+		g1b-p0-2-hog {
 			gpio-hog;
 			gpios = <2 0>;
 			input;
 			line-name = "PVDDQ_GHJ_PINALERT_N";
 		};
-		G1B_P0_3 {
+		g1b-p0-3-hog {
 			gpio-hog;
 			gpios = <3 0>;
 			input;
 			line-name = "PVDDQ_KLM_PINALERT_N";
 		};
-		G1B_P0_5 {
+		g1b-p0-5-hog {
 			gpio-hog;
 			gpios = <5 0>;
 			input;
 			line-name = "FM_BOARD_REV_ID0";
 		};
-		G1B_P0_6 {
+		g1b-p0-6-hog {
 			gpio-hog;
 			gpios = <6 0>;
 			input;
 			line-name = "FM_BOARD_REV_ID1";
 		};
-		G1B_P0_7 {
+		g1b-p0-7-hog {
 			gpio-hog;
 			gpios = <7 0>;
 			input;
 			line-name = "FM_BOARD_REV_ID2";
 		};
-		G1B_P1_0 {
+		g1b-p1-0-hog {
 			gpio-hog;
 			gpios = <8 0>;
 			input;
 			line-name = "FM_OC_DETECT_EN_N";
 		};
-		G1B_P1_1 {
+		g1b-p1-1-hog {
 			gpio-hog;
 			gpios = <9 0>;
 			input;
 			line-name = "FM_FLASH_DESC_OVERRIDE";
 		};
-		G1B_P1_2 {
+		g1b-p1-2-hog {
 			gpio-hog;
 			gpios = <10 0>;
 			output-low;
 			line-name = "FP_PWR_ID_LED_N";
 		};
-		G1B_P1_3 {
+		g1b-p1-3-hog {
 			gpio-hog;
 			gpios = <11 0>;
 			output-low;
 			line-name = "BMC_LED_PWR_GRN";
 		};
-		G1B_P1_4 {
+		g1b-p1-4-hog {
 			gpio-hog;
 			gpios = <12 0>;
 			output-low;
 			line-name = "BMC_LED_PWR_AMBER";
 		};
-		G1B_P1_5 {
+		g1b-p1-5-hog {
 			gpio-hog;
 			gpios = <13 0>;
 			output-high;
 			line-name = "FM_BMC_FAULT_LED_N";
 		};
-		G1B_P1_6 {
+		g1b-p1-6-hog {
 			gpio-hog;
 			gpios = <14 0>;
 			output-high;
 			line-name = "FM_CPLD_BMC_PWRDN_N";
 		};
-		G1B_P1_7 {
+		g1b-p1-7-hog {
 			gpio-hog;
 			gpios = <15 0>;
 			output-high;
@ -626,91 +626,91 @@
 		gpio-controller;
 		#gpio-cells = <2>;
 		reset-gpios = <&gpio5 28 GPIO_ACTIVE_LOW>;
-		G2A_P0_0 {
+		g2a-p0-0-hog {
 			gpio-hog;
 			gpios = <0 0>;
 			output-high;
 			line-name = "BMC_PON_RST_REQ_N";
 		};
-		G2A_P0_1 {
+		g2a-p0-1-hog {
 			gpio-hog;
 			gpios = <1 0>;
 			output-high;
 			line-name = "BMC_RST_IND_REQ_N";
 		};
-		G2A_P0_2 {
+		g2a-p0-2-hog {
 			gpio-hog;
 			gpios = <2 0>;
 			input;
 			line-name = "RST_BMC_RTCRST";
 		};
-		G2A_P0_3 {
+		g2a-p0-3-hog {
 			gpio-hog;
 			gpios = <3 0>;
 			output-high;
 			line-name = "FM_BMC_PWRBTN_OUT_N";
 		};
-		G2A_P0_4 {
+		g2a-p0-4-hog {
 			gpio-hog;
 			gpios = <4 0>;
 			output-high;
 			line-name = "RST_BMC_SYSRST_BTN_OUT_N";
 		};
-		G2A_P0_5 {
+		g2a-p0-5-hog {
 			gpio-hog;
 			gpios = <5 0>;
 			output-high;
 			line-name = "FM_BATTERY_SENSE_EN_N";
 		};
-		G2A_P0_6 {
+		g2a-p0-6-hog {
 			gpio-hog;
 			gpios = <6 0>;
 			output-high;
 			line-name = "FM_BMC_READY_N";
 		};
-		G2A_P0_7 {
+		g2a-p0-7-hog {
 			gpio-hog;
 			gpios = <7 0>;
 			input;
 			line-name = "IRQ_BMC_PCH_SMI_LPC_N";
 		};
-		G2A_P1_0 {
+		g2a-p1-0-hog {
 			gpio-hog;
 			gpios = <8 0>;
 			input;
 			line-name = "FM_SLOT4_CFG0";
 		};
-		G2A_P1_1 {
+		g2a-p1-1-hog {
 			gpio-hog;
 			gpios = <9 0>;
 			input;
 			line-name = "FM_SLOT4_CFG1";
 		};
-		G2A_P1_2 {
+		g2a-p1-2-hog {
 			gpio-hog;
 			gpios = <10 0>;
 			input;
 			line-name = "FM_NVDIMM_EVENT_N";
 		};
-		G2A_P1_3 {
+		g2a-p1-3-hog {
 			gpio-hog;
 			gpios = <11 0>;
 			input;
 			line-name = "PSU1_BLADE_EN_N";
 		};
-		G2A_P1_4 {
+		g2a-p1-4-hog {
 			gpio-hog;
 			gpios = <12 0>;
 			input;
 			line-name = "BMC_PCH_FNM";
 		};
-		G2A_P1_5 {
+		g2a-p1-5-hog {
 			gpio-hog;
 			gpios = <13 0>;
 			input;
 			line-name = "FM_SOL_UART_CH_SEL";
 		};
-		G2A_P1_6 {
+		g2a-p1-6-hog {
 			gpio-hog;
 			gpios = <14 0>;
 			input;
@ -723,91 +723,91 @@
 		reg = <0x75>;
 		gpio-controller;
 		#gpio-cells = <2>;
-		G2B_P0_0 {
+		g2b-p0-0-hog {
 			gpio-hog;
 			gpios = <0 0>;
 			input;
 			line-name = "FM_CPU_MSMI_LVT3_N";
 		};
-		G2B_P0_1 {
+		g2b-p0-1-hog {
 			gpio-hog;
 			gpios = <1 0>;
 			input;
 			line-name = "FM_BIOS_MRC_DEBUG_MSG_DIS";
 		};
-		G2B_P0_2 {
+		g2b-p0-2-hog {
 			gpio-hog;
 			gpios = <2 0>;
 			input;
 			line-name = "FM_CPU1_DISABLE_BMC_N";
 		};
-		G2B_P0_3 {
+		g2b-p0-3-hog {
 			gpio-hog;
 			gpios = <3 0>;
 			output-low;
 			line-name = "BMC_JTAG_SELECT";
 		};
-		G2B_P0_4 {
+		g2b-p0-4-hog {
 			gpio-hog;
 			gpios = <4 0>;
 			output-high;
 			line-name = "PECI_MUX_SELECT";
 		};
-		G2B_P0_5 {
+		g2b-p0-5-hog {
 			gpio-hog;
 			gpios = <5 0>;
 			output-high;
 			line-name = "I2C_MUX2_RESET_N";
 		};
-		G2B_P0_6 {
+		g2b-p0-6-hog {
 			gpio-hog;
 			gpios = <6 0>;
 			input;
 			line-name = "FM_BMC_CPLD_PSU2_ON";
 		};
-		G2B_P0_7 {
+		g2b-p0-7-hog {
 			gpio-hog;
 			gpios = <7 0>;
 			output-high;
 			line-name = "PSU2_ALERT_EN_N";
 		};
-		G2B_P1_0 {
+		g2b-p1-0-hog {
 			gpio-hog;
 			gpios = <8 0>;
 			output-high;
 			line-name = "FM_CPU_BMC_INIT";
 		};
-		G2B_P1_1 {
+		g2b-p1-1-hog {
 			gpio-hog;
 			gpios = <9 0>;
 			output-high;
 			line-name = "IRQ_BMC_PCH_SCI_LPC_N";
 		};
-		G2B_P1_2 {
+		g2b-p1-2-hog {
 			gpio-hog;
 			gpios = <10 0>;
 			output-low;
 			line-name = "PMB_ALERT_EN_N";
 		};
-		G2B_P1_3 {
+		g2b-p1-3-hog {
 			gpio-hog;
 			gpios = <11 0>;
 			output-high;
 			line-name = "FM_FAST_PROCHOT_EN_N";
 		};
-		G2B_P1_4 {
+		g2b-p1-4-hog {
 			gpio-hog;
 			gpios = <12 0>;
 			output-high;
 			line-name = "BMC_NVDIMM_PRSNT_N";
 		};
-		G2B_P1_5 {
+		g2b-p1-5-hog {
 			gpio-hog;
 			gpios = <13 0>;
 			output-low;
 			line-name = "FM_BACKUP_BIOS_SEL_H_BMC";
 		};
-		G2B_P1_6 {
+		g2b-p1-6-hog {
 			gpio-hog;
 			gpios = <14 0>;
 			output-high;
--- a/arch/arm/boot/dts/nuvoton/nuvoton-npcm750.dtsi
+++ b/arch/arm/boot/dts/nuvoton/nuvoton-npcm750.dtsi
@ -58,5 +58,70 @@
 					&rg2mdio_pins>;
 			status = "disabled";
 		};
+
+		udc0: usb@f0830000 {
+			compatible = "nuvoton,npcm750-udc";
+			reg = <0xf0830000 0x1000
+			       0xfffd0000 0x800>;
+			interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk NPCM7XX_CLK_SU>;
+			clock-names = "clk_usb_bridge";
+			phys = <&udc0_phy>;
+			phy_type = "utmi_wide";
+			dr_mode = "peripheral";
+			status = "disabled";
+		};
+
+		udc1: usb@f0831000 {
+			compatible = "nuvoton,npcm750-udc";
+			reg = <0xf0831000 0x1000
+			       0xfffd0800 0x800>;
+			interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk NPCM7XX_CLK_SU>;
+			clock-names = "clk_usb_bridge";
+			phys = <&udc0_phy>;
+			phy_type = "utmi_wide";
+			dr_mode = "peripheral";
+			status = "disabled";
+		};
+
+		udc2: usb@f0832000 {
+			compatible = "nuvoton,npcm750-udc";
+			reg = <0xf0832000 0x1000
+			       0xfffd1000 0x800>;
+			interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk NPCM7XX_CLK_SU>;
+			clock-names = "clk_usb_bridge";
+			phys = <&udc0_phy>;
+			phy_type = "utmi_wide";
+			dr_mode = "peripheral";
+			status = "disabled";
+		};
+
+		udc3: usb@f0833000 {
+			compatible = "nuvoton,npcm750-udc";
+			reg = <0xf0833000 0x1000
+			       0xfffd1800 0x800>;
+			interrupts = <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk NPCM7XX_CLK_SU>;
+			clock-names = "clk_usb_bridge";
+			phys = <&udc0_phy>;
+			phy_type = "utmi_wide";
+			dr_mode = "peripheral";
+			status = "disabled";
+		};
+
+		udc4: usb@f0834000 {
+			compatible = "nuvoton,npcm750-udc";
+			reg = <0xf0834000 0x1000
+			       0xfffd2000 0x800>;
+			interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk NPCM7XX_CLK_SU>;
+			clock-names = "clk_usb_bridge";
+			phys = <&udc0_phy>;
+			phy_type = "utmi_wide";
+			dr_mode = "peripheral";
+			status = "disabled";
+		};
 	};
 };
--- a/arch/arm/boot/dts/nvidia/Makefile
+++ b/arch/arm/boot/dts/nvidia/Makefile
@ -34,6 +34,7 @@ dtb-$(CONFIG_ARCH_TEGRA_3x_SOC) += \
 	tegra30-asus-tf201.dtb \
 	tegra30-asus-tf300t.dtb \
 	tegra30-asus-tf300tg.dtb \
+	tegra30-asus-tf300tl.dtb \
 	tegra30-asus-tf700t.dtb \
 	tegra30-beaver.dtb \
 	tegra30-cardhu-a02.dtb \
--- a/arch/arm/boot/dts/nvidia/tegra124-apalis-eval.dts
+++ b/arch/arm/boot/dts/nvidia/tegra124-apalis-eval.dts
@ -84,11 +84,6 @@
 		status = "okay";
 		clock-frequency = <400000>;

-		pcie-switch@58 {
-			compatible = "plx,pex8605";
-			reg = <0x58>;
-		};
-
 		/* M41T0M6 real time clock on carrier board */
 		rtc@68 {
 			compatible = "st,m41t0";
--- a/arch/arm/boot/dts/nvidia/tegra124-apalis-v1.2-eval.dts
+++ b/arch/arm/boot/dts/nvidia/tegra124-apalis-v1.2-eval.dts
@ -85,11 +85,6 @@
 		status = "okay";
 		clock-frequency = <400000>;

-		pcie-switch@58 {
-			compatible = "plx,pex8605";
-			reg = <0x58>;
-		};
-
 		/* M41T0M6 real time clock on carrier board */
 		rtc@68 {
 			compatible = "st,m41t0";
--- a/arch/arm/boot/dts/nvidia/tegra20.dtsi
+++ b/arch/arm/boot/dts/nvidia/tegra20.dtsi
@ -284,7 +284,7 @@
 		reg = <0x60007000 0x1000>;
 	};

-	apbdma: dma@6000a000 {
+	apbdma: dma-controller@6000a000 {
 		compatible = "nvidia,tegra20-apbdma";
 		reg = <0x6000a000 0x1200>;
 		interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>,
--- a/arch/arm/boot/dts/nvidia/tegra30-apalis-eval.dts
+++ b/arch/arm/boot/dts/nvidia/tegra30-apalis-eval.dts
@ -91,11 +91,6 @@
 		status = "okay";
 		clock-frequency = <400000>;

-		pcie-switch@58 {
-			compatible = "plx,pex8605";
-			reg = <0x58>;
-		};
-
 		/* M41T0M6 real time clock on carrier board */
 		rtc@68 {
 			compatible = "st,m41t0";
--- a/arch/arm/boot/dts/nvidia/tegra30-apalis-v1.1-eval.dts
+++ b/arch/arm/boot/dts/nvidia/tegra30-apalis-v1.1-eval.dts
@ -92,11 +92,6 @@
 		status = "okay";
 		clock-frequency = <400000>;

-		pcie-switch@58 {
-			compatible = "plx,pex8605";
-			reg = <0x58>;
-		};
-
 		/* M41T0M6 real time clock on carrier board */
 		rtc@68 {
 			compatible = "st,m41t0";
--- a/arch/arm/boot/dts/nvidia/tegra30-asus-tf300tl.dts
+++ b/arch/arm/boot/dts/nvidia/tegra30-asus-tf300tl.dts
@ -0,0 +1,857 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include "tegra30-asus-transformer-common.dtsi"
+#include "tegra30-asus-lvds-display.dtsi"
+
+/ {
+	model = "Asus Transformer Pad LTE TF300TL";
+	compatible = "asus,tf300tl", "nvidia,tegra30";
+
+	gpio@6000d000 {
+		tf300tl-init-hog {
+			gpio-hog;
+			gpios = <TEGRA_GPIO(C, 6) GPIO_ACTIVE_HIGH>;
+			output-low;
+		};
+	};
+
+	pinmux@70000868 {
+		state_default: pinmux {
+			lcd_pwr2_pc6 {
+				nvidia,pins = "lcd_pwr2_pc6",
+					      "lcd_dc1_pd2";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			pbb3 {
+				nvidia,pins = "pbb3";
+				nvidia,function = "vgp3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			pbb7 {
+				nvidia,pins = "pbb7";
+				nvidia,function = "i2s4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			kb_row7_pr7 {
+				nvidia,pins = "kb_row7_pr7";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			gmi_cs4_n_pk2 {
+				nvidia,pins = "gmi_cs4_n_pk2";
+				nvidia,function = "gmi";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			ulpi_data5_po6 {
+				nvidia,pins = "ulpi_data5_po6";
+				nvidia,function = "uarta";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			dap3_din_pp1 {
+				nvidia,pins = "dap3_din_pp1";
+				nvidia,function = "i2s2";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			crt_hsync_pv6 {
+				nvidia,pins = "crt_hsync_pv6";
+				nvidia,function = "crt";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			crt_vsync_pv7 {
+				nvidia,pins = "crt_vsync_pv7";
+				nvidia,function = "crt";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			pu5 {
+				nvidia,pins = "pu5";
+				nvidia,function = "pwm2";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			clk3_out_pee0 {
+				nvidia,pins = "clk3_out_pee0";
+				nvidia,function = "extperiph3";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			clk3_req_pee1 {
+				nvidia,pins = "clk3_req_pee1";
+				nvidia,function = "dev3";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			dap1_fs_pn0 {
+				nvidia,pins = "dap1_fs_pn0",
+						"dap1_sclk_pn3";
+				nvidia,function = "i2s0";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			dap1_din_pn1 {
+				nvidia,pins = "dap1_din_pn1";
+				nvidia,function = "i2s0";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			dap1_dout_pn2 {
+				nvidia,pins = "dap1_dout_pn2";
+				nvidia,function = "i2s0";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			clk1_req_pee2 {
+				nvidia,pins = "clk1_req_pee2";
+				nvidia,function = "dap";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			spi2_mosi_px0 {
+				nvidia,pins = "spi2_mosi_px0";
+				nvidia,function = "spi2";
+			};
+
+			spi1_sck_px5 {
+				nvidia,pins = "spi1_sck_px5";
+				nvidia,function = "spi1";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			spi1_miso_px7 {
+				nvidia,pins = "spi1_miso_px7";
+				nvidia,function = "spi1";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			spi2_cs2_n_pw3 {
+				nvidia,pins = "spi2_cs2_n_pw3";
+				nvidia,function = "spi2";
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+			};
+		};
+	};
+
+	serial@70006200 {
+		/* Azurewave AW-NH615 BCM4329B1 */
+		bluetooth {
+			compatible = "brcm,bcm4329-bt";
+		};
+	};
+
+	i2c@7000c400 {
+		/* Elantech EKTH1036 touchscreen */
+		touchscreen@10 {
+			compatible = "elan,ektf3624";
+			reg = <0x10>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(H, 4) IRQ_TYPE_EDGE_FALLING>;
+			reset-gpios = <&gpio TEGRA_GPIO(H, 6) GPIO_ACTIVE_LOW>;
+
+			vcc33-supply = <&vdd_3v3_sys>;
+			vccio-supply = <&vdd_3v3_sys>;
+
+			touchscreen-size-x = <2240>;
+			touchscreen-size-y = <1408>;
+			touchscreen-inverted-y;
+		};
+	};
+
+	i2c@7000c500 {
+		clock-frequency = <400000>;
+
+		magnetometer@e {
+			mount-matrix =  "-1",  "0",  "0",
+					 "0", "-1",  "0",
+					 "0",  "0",  "1";
+		};
+
+		gyroscope@68 {
+			mount-matrix =   "-1",  "0",  "0",
+					  "0",  "1",  "0",
+					  "0",  "0", "-1";
+
+			/* External I2C interface */
+			i2c-gate {
+				accelerometer@f {
+					mount-matrix =   "0", "-1",  "0",
+							"-1",  "0",  "0",
+							 "0",  "0",  "1";
+				};
+			};
+		};
+	};
+
+	i2c@7000d000 {
+		/* Realtek ALC5631 audio codec */
+		rt5631: audio-codec@1a {
+			compatible = "realtek,rt5631";
+			reg = <0x1a>;
+		};
+	};
+
+	memory-controller@7000f000 {
+		emc-timings-0 {
+			/* Elpida 1GB 667MHZ */
+			nvidia,ram-code = <0>;
+
+			timing-25500000 {
+				clock-frequency = <25500000>;
+
+				nvidia,emem-configuration = < 0x00020001 0xc0000020
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0502 0x74830303 0x001f0000 >;
+			};
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+
+				nvidia,emem-configuration = < 0x00010001 0xc0000020
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0502 0x73430303 0x001f0000 >;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emem-configuration = < 0x00000001 0xc0000030
+					0x00000001 0x00000001 0x00000003 0x00000000
+					0x00000001 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0503 0x72830504 0x001f0000 >;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emem-configuration = < 0x00000003 0xc0000025
+					0x00000001 0x00000001 0x00000005 0x00000002
+					0x00000003 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0505 0x72440a06 0x001f0000 >;
+			};
+
+			timing-333500000 {
+				clock-frequency = <333500000>;
+
+				nvidia,emem-configuration = < 0x00000005 0xc000003d
+					0x00000001 0x00000002 0x00000008 0x00000004
+					0x00000004 0x00000001 0x00000002 0x00000007
+					0x00000002 0x00000002 0x00000003 0x00000006
+					0x06030202 0x000b0608 0x70850f09 0x001f0000 >;
+			};
+
+			timing-667000000 {
+				clock-frequency = <667000000>;
+
+				nvidia,emem-configuration = < 0x0000000a 0xc0000079
+					0x00000003 0x00000004 0x00000010 0x0000000b
+					0x0000000a 0x00000001 0x00000003 0x0000000b
+					0x00000002 0x00000002 0x00000004 0x00000008
+					0x08040202 0x00130b10 0x70ea1f11 0x001f0000 >;
+			};
+		};
+
+		emc-timings-1 {
+			/* Hynix 1GB 667MHZ */
+			nvidia,ram-code = <1>;
+
+			timing-25500000 {
+				clock-frequency = <25500000>;
+
+				nvidia,emem-configuration = < 0x00020001 0xc0000020
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0502 0x74830303 0x001f0000 >;
+			};
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+
+				nvidia,emem-configuration = < 0x00010001 0xc0000020
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0502 0x73430303 0x001f0000 >;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emem-configuration = < 0x00000001 0xc0000030
+					0x00000001 0x00000001 0x00000003 0x00000000
+					0x00000001 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0503 0x72830504 0x001f0000 >;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emem-configuration = < 0x00000003 0xc0000025
+					0x00000001 0x00000001 0x00000005 0x00000002
+					0x00000003 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0505 0x72440a06 0x001f0000 >;
+			};
+
+			timing-333500000 {
+				clock-frequency = <333500000>;
+
+				nvidia,emem-configuration = < 0x00000005 0xc000003d
+					0x00000001 0x00000002 0x00000008 0x00000004
+					0x00000004 0x00000001 0x00000002 0x00000007
+					0x00000002 0x00000002 0x00000003 0x00000006
+					0x06030202 0x000b0608 0x70850f09 0x001f0000 >;
+			};
+
+			timing-667000000 {
+				clock-frequency = <667000000>;
+
+				nvidia,emem-configuration = < 0x0000000a 0xc0000079
+					0x00000003 0x00000004 0x00000010 0x0000000b
+					0x0000000a 0x00000001 0x00000003 0x0000000b
+					0x00000002 0x00000002 0x00000004 0x00000008
+					0x08040202 0x00130b10 0x70ea1f11 0x001f0000 >;
+			};
+		};
+	};
+
+	memory-controller@7000f400 {
+		emc-timings-0 {
+			/* Elpida 1GB 667MHZ */
+			nvidia,ram-code = <0>;
+
+			timing-25500000 {
+				clock-frequency = <25500000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200048>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000001
+					0x00000004 0x00000000 0x00000000 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000000
+					0x00000000 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000005 0x00000004 0x0000000a
+					0x0000000b 0x000000c0 0x00000000 0x00000030
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x00000005 0x00000005
+					0x00000004 0x00000001 0x00000000 0x00000004
+					0x00000005 0x000000c7 0x00000006 0x00000004
+					0x00000000 0x00000000 0x00004288 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00000000
+					0x00000040 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x80000287 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200048>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000002
+					0x00000008 0x00000001 0x00000000 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000000
+					0x00000000 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000005 0x00000004 0x0000000a
+					0x0000000b 0x00000181 0x00000000 0x00000060
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x00000009 0x00000009
+					0x00000004 0x00000002 0x00000000 0x00000004
+					0x00000005 0x0000018e 0x00000006 0x00000004
+					0x00000000 0x00000000 0x00004288 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00000000
+					0x00000040 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x8000040b 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200048>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000005
+					0x00000010 0x00000003 0x00000001 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000001
+					0x00000001 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000005 0x00000004 0x0000000a
+					0x0000000b 0x00000303 0x00000000 0x000000c0
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x00000012 0x00000012
+					0x00000004 0x00000004 0x00000000 0x00000004
+					0x00000005 0x0000031c 0x00000006 0x00000004
+					0x00000000 0x00000000 0x00004288 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00000000
+					0x00000040 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x80000713 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200048>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x0000000a
+					0x00000020 0x00000007 0x00000002 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000002
+					0x00000002 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000006 0x00000004 0x0000000a
+					0x0000000b 0x00000607 0x00000000 0x00000181
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x00000023 0x00000023
+					0x00000004 0x00000007 0x00000000 0x00000004
+					0x00000005 0x00000638 0x00000007 0x00000004
+					0x00000000 0x00000000 0x00004288 0x004400a4
+					0x00008000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00020000
+					0x00000100 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x80000d22 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-333500000 {
+				clock-frequency = <333500000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100002>;
+				nvidia,emc-mode-2 = <0x80200040>;
+				nvidia,emc-mode-reset = <0x80000321>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+
+				nvidia,emc-configuration =  < 0x0000000f
+					0x00000034 0x0000000a 0x00000003 0x00000003
+					0x00000008 0x00000002 0x00000009 0x00000003
+					0x00000003 0x00000002 0x00000001 0x00000000
+					0x00000004 0x00000006 0x00000004 0x0000000a
+					0x0000000c 0x000009e9 0x00000000 0x0000027a
+					0x00000001 0x00000008 0x00000001 0x00000000
+					0x00000007 0x0000000e 0x00000039 0x00000200
+					0x00000004 0x0000000a 0x00000000 0x00000004
+					0x00000005 0x00000a2a 0x00000000 0x00000004
+					0x00000000 0x00000000 0x00007088 0x002600a4
+					0x00008000 0x0003c000 0x0003c000 0x0003c000
+					0x0003c000 0x00014000 0x00014000 0x00014000
+					0x00014000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00050000 0x00050000 0x00050000
+					0x00050000 0x000002a0 0x0800013d 0x00000000
+					0x77fff884 0x01f1f508 0x05057404 0x54000007
+					0x080001e8 0x08000021 0x00000802 0x00020000
+					0x00000100 0x018b000c 0xa0f10000 0x00000000
+					0x00000000 0x800014d4 0xe8000000 0xff00ff89 >;
+			};
+
+			timing-667000000 {
+				clock-frequency = <667000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100002>;
+				nvidia,emc-mode-2 = <0x80200058>;
+				nvidia,emc-mode-reset = <0x80000b71>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x0000001f
+					0x00000069 0x00000017 0x00000007 0x00000005
+					0x0000000c 0x00000003 0x00000011 0x00000007
+					0x00000007 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000b 0x00000009 0x0000000b
+					0x00000011 0x00001412 0x00000000 0x00000504
+					0x00000002 0x0000000e 0x00000001 0x00000000
+					0x0000000c 0x00000016 0x00000072 0x00000200
+					0x00000005 0x00000015 0x00000000 0x00000006
+					0x00000007 0x00001453 0x0000000c 0x00000004
+					0x00000000 0x00000000 0x00005088 0xf00b0191
+					0x00008000 0x0000000a 0x0000000a 0x0000000a
+					0x0000000a 0x0000000a 0x0000000a 0x0000000a
+					0x0000000a 0x00018000 0x00018000 0x00018000
+					0x00018000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x0000000c 0x0000000c 0x0000000c
+					0x0000000c 0x000002a0 0x0800013d 0x22220000
+					0x77fff884 0x01f1f501 0x07077404 0x54000000
+					0x080001e8 0x0a000021 0x00000802 0x00020000
+					0x00000100 0x0156000c 0xa0f10000 0x00000000
+					0x00000000 0x800028a5 0xe8000000 0xff00ff49 >;
+			};
+		};
+
+		emc-timings-1 {
+			/* Hynix 1GB 667MHZ */
+			nvidia,ram-code = <1>;
+
+			timing-25500000 {
+				clock-frequency = <25500000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200048>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000001
+					0x00000004 0x00000000 0x00000000 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000000
+					0x00000000 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000005 0x00000004 0x0000000a
+					0x0000000b 0x000000c0 0x00000000 0x00000030
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x00000005 0x00000005
+					0x00000004 0x00000001 0x00000000 0x00000004
+					0x00000005 0x000000c7 0x00000006 0x00000004
+					0x00000000 0x00000000 0x00004288 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00000000
+					0x00000040 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x80000287 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200048>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000002
+					0x00000008 0x00000001 0x00000000 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000000
+					0x00000000 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000005 0x00000004 0x0000000a
+					0x0000000b 0x00000181 0x00000000 0x00000060
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x00000009 0x00000009
+					0x00000004 0x00000002 0x00000000 0x00000004
+					0x00000005 0x0000018e 0x00000006 0x00000004
+					0x00000000 0x00000000 0x00004288 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00000000
+					0x00000040 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x8000040b 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200048>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000005
+					0x00000010 0x00000003 0x00000001 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000001
+					0x00000001 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000005 0x00000004 0x0000000a
+					0x0000000b 0x00000303 0x00000000 0x000000c0
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x00000012 0x00000012
+					0x00000004 0x00000004 0x00000000 0x00000004
+					0x00000005 0x0000031c 0x00000006 0x00000004
+					0x00000000 0x00000000 0x00004288 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00000000
+					0x00000040 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x80000713 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200048>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x0000000a
+					0x00000020 0x00000007 0x00000002 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000002
+					0x00000002 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000006 0x00000004 0x0000000a
+					0x0000000b 0x00000607 0x00000000 0x00000181
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x00000023 0x00000023
+					0x00000004 0x00000007 0x00000000 0x00000004
+					0x00000005 0x00000638 0x00000007 0x00000004
+					0x00000000 0x00000000 0x00004288 0x004400a4
+					0x00008000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00020000
+					0x00000100 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x80000d22 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-333500000 {
+				clock-frequency = <333500000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100002>;
+				nvidia,emc-mode-2 = <0x80200040>;
+				nvidia,emc-mode-reset = <0x80000321>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+
+				nvidia,emc-configuration =  < 0x0000000f
+					0x00000034 0x0000000a 0x00000003 0x00000003
+					0x00000008 0x00000002 0x00000009 0x00000003
+					0x00000003 0x00000002 0x00000001 0x00000000
+					0x00000004 0x00000006 0x00000004 0x0000000a
+					0x0000000c 0x000009e9 0x00000000 0x0000027a
+					0x00000001 0x00000008 0x00000001 0x00000000
+					0x00000007 0x0000000e 0x00000039 0x00000200
+					0x00000004 0x0000000a 0x00000000 0x00000004
+					0x00000005 0x00000a2a 0x00000000 0x00000004
+					0x00000000 0x00000000 0x00007088 0x002600a4
+					0x00008000 0x0003c000 0x0003c000 0x0003c000
+					0x0003c000 0x00014000 0x00014000 0x00014000
+					0x00014000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00048000 0x00048000 0x00048000
+					0x00048000 0x000002a0 0x0800013d 0x00000000
+					0x77fff884 0x01f1f508 0x05057404 0x54000007
+					0x080001e8 0x08000021 0x00000802 0x00020000
+					0x00000100 0x018b000c 0xa0f10000 0x00000000
+					0x00000000 0x800014d4 0xe8000000 0xff00ff89 >;
+			};
+
+			timing-667000000 {
+				clock-frequency = <667000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100002>;
+				nvidia,emc-mode-2 = <0x80200058>;
+				nvidia,emc-mode-reset = <0x80000b71>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000020
+					0x00000069 0x00000017 0x00000007 0x00000005
+					0x0000000c 0x00000003 0x00000011 0x00000007
+					0x00000007 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000b 0x00000009 0x0000000b
+					0x00000011 0x00001412 0x00000000 0x00000504
+					0x00000002 0x0000000e 0x00000001 0x00000000
+					0x0000000c 0x00000016 0x00000072 0x00000200
+					0x00000005 0x00000015 0x00000000 0x00000006
+					0x00000007 0x00001453 0x0000000c 0x00000004
+					0x00000000 0x00000000 0x00005088 0xf00b0191
+					0x00008000 0x0000000a 0x0000000a 0x0000000a
+					0x0000000a 0x0000000a 0x0000000a 0x0000000a
+					0x0000000a 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x0000000c 0x0000000c 0x0000000c
+					0x0000000c 0x000002a0 0x0600013d 0x22220000
+					0x77fff884 0x01f1f501 0x07077404 0x54000000
+					0x080001e8 0x08000021 0x00000802 0x00020000
+					0x00000100 0x0156000c 0xa0f10000 0x00000000
+					0x00000000 0x800028a5 0xf8000000 0xff00ff49 >;
+			};
+		};
+	};
+
+	pad_battery: battery-pad {
+		compatible = "simple-battery";
+		device-chemistry = "lithium-ion-polymer";
+		charge-full-design-microamp-hours = <2940000>;
+		energy-full-design-microwatt-hours = <22000000>;
+		operating-range-celsius = <0 45>;
+	};
+
+	dock_battery: battery-dock {
+		compatible = "simple-battery";
+		device-chemistry = "lithium-ion-polymer";
+		charge-full-design-microamp-hours = <2260000>;
+		energy-full-design-microwatt-hours = <16000000>;
+		operating-range-celsius = <0 45>;
+	};
+
+	display-panel {
+		compatible = "innolux,g101ice-l01";
+	};
+
+	opp-table-emc {
+		/delete-node/ opp-750000000-1300;
+		/delete-node/ opp-800000000-1300;
+		/delete-node/ opp-900000000-1350;
+	};
+
+	opp-table-actmon {
+		/delete-node/ opp-750000000;
+		/delete-node/ opp-800000000;
+		/delete-node/ opp-900000000;
+	};
+
+	sound {
+		compatible = "asus,tegra-audio-rt5631-tf300tl",
+			     "nvidia,tegra-audio-rt5631";
+		nvidia,model = "Asus Transformer Pad TF300TL RT5631";
+
+		nvidia,audio-routing =
+			"Headphone Jack", "HPOL",
+			"Headphone Jack", "HPOR",
+			"Int Spk", "SPOL",
+			"Int Spk", "SPOR",
+			"MIC1", "MIC Bias1",
+			"MIC Bias1", "Mic Jack",
+			"DMIC", "Int Mic";
+
+		nvidia,audio-codec = <&rt5631>;
+	};
+};
--- a/arch/arm/boot/dts/nvidia/tegra30.dtsi
+++ b/arch/arm/boot/dts/nvidia/tegra30.dtsi
@ -431,7 +431,7 @@
 		reg = <0x60007000 0x1000>;
 	};

-	apbdma: dma@6000a000 {
+	apbdma: dma-controller@6000a000 {
 		compatible = "nvidia,tegra30-apbdma", "nvidia,tegra20-apbdma";
 		reg = <0x6000a000 0x1400>;
 		interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>,
--- a/arch/arm/boot/dts/nxp/imx/imx25.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx25.dtsi
@ -611,7 +611,7 @@
 			reg = <0x80000000 0x3b002000>;
 			ranges;

-			nfc: nand@bb000000 {
+			nfc: nand-controller@bb000000 {
 				#address-cells = <1>;
 				#size-cells = <1>;

--- a/arch/arm/boot/dts/nxp/imx/imx31-lite.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx31-lite.dts
@ -157,7 +157,7 @@
 &weim {
 	status = "okay";

-	nor@0,0 {
+	flash@0,0 {
 		compatible = "cfi-flash";
 		reg = <0 0x0 0x200000>;
 		bank-width = <2>;
--- a/arch/arm/boot/dts/nxp/imx/imx31.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx31.dtsi
@ -218,7 +218,7 @@
 			};

 			iim: efuse@5001c000 {
-				compatible = "fsl,imx31-iim", "fsl,imx27-iim";
+				compatible = "fsl,imx31-iim";
 				reg = <0x5001c000 0x1000>;
 				interrupts = <19>;
 				clocks = <&clks 25>;
--- a/arch/arm/boot/dts/nxp/imx/imx35.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx35.dtsi
@ -363,7 +363,7 @@
 			reg = <0x80000000 0x40000000>;
 			ranges;

-			nfc: nand@bb000000 {
+			nfc: nand-controller@bb000000 {
 				#address-cells = <1>;
 				#size-cells = <1>;
 				compatible = "fsl,imx35-nand", "fsl,imx25-nand";
--- a/arch/arm/boot/dts/nxp/imx/imx51-digi-connectcore-som.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx51-digi-connectcore-som.dtsi
@ -165,7 +165,7 @@
 	mma7455l@1d {
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_mma7455l>;
-		compatible = "fsl,mma7455l";
+		compatible = "fsl,mma7455";
 		reg = <0x1d>;
 		interrupt-parent = <&gpio1>;
 		interrupts = <7 IRQ_TYPE_LEVEL_HIGH>, <6 IRQ_TYPE_LEVEL_HIGH>;
--- a/arch/arm/boot/dts/nxp/imx/imx51.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx51.dtsi
@ -476,7 +476,7 @@
 			};

 			iim: efuse@83f98000 {
-				compatible = "fsl,imx51-iim", "fsl,imx27-iim", "syscon";
+				compatible = "fsl,imx51-iim";
 				reg = <0x83f98000 0x4000>;
 				interrupts = <69>;
 				clocks = <&clks IMX5_CLK_IIM_GATE>;
@ -595,7 +595,7 @@
 				status = "disabled";
 			};

-			nfc: nand@83fdb000 {
+			nfc: nand-controller@83fdb000 {
 				#address-cells = <1>;
 				#size-cells = <1>;
 				compatible = "fsl,imx51-nand";
--- a/arch/arm/boot/dts/nxp/imx/imx53.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx53.dtsi
@ -668,7 +668,7 @@
 			};

 			iim: efuse@63f98000 {
-				compatible = "fsl,imx53-iim", "fsl,imx27-iim", "syscon";
+				compatible = "fsl,imx53-iim";
 				reg = <0x63f98000 0x4000>;
 				interrupts = <69>;
 				clocks = <&clks IMX5_CLK_IIM_GATE>;
@ -775,7 +775,7 @@
 				status = "disabled";
 			};

-			nfc: nand@63fdb000 {
+			nfc: nand-controller@63fdb000 {
 				compatible = "fsl,imx53-nand";
 				reg = <0x63fdb000 0x1000 0xf7ff0000 0x10000>;
 				interrupts = <8>;
--- a/arch/arm/boot/dts/nxp/imx/imx6q-apalis-eval.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-apalis-eval.dts
@ -36,15 +36,6 @@
 	status = "okay";
 };

-/* I2C1_SDA/SCL on MXM3 209/211 (e.g. RTC on carrier board) */
-&i2c1 {
-	/* PCIe Switch */
-	pcie-switch@58 {
-		compatible = "plx,pex8605";
-		reg = <0x58>;
-	};
-};
-
 &pcie {
 	vpcie-supply = <&reg_pcie_switch>;
 	status = "okay";
--- a/arch/arm/boot/dts/nxp/imx/imx6q-mccmon6.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-mccmon6.dts
@ -279,7 +279,7 @@
 	ranges = <0 0 0x08000000 0x08000000>;
 	status = "okay";

-	nor@0,0 {
+	flash@0,0 {
 		compatible = "cfi-flash";
 		reg = <0 0 0x02000000>;
 		#address-cells = <1>;
--- a/arch/arm/boot/dts/nxp/imx/imx6qdl-sabreauto.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-sabreauto.dtsi
@ -854,7 +854,7 @@
 	ranges = <0 0 0x08000000 0x08000000>;
 	status = "disabled"; /* pin conflict with SPI NOR */

-	nor@0,0 {
+	flash@0,0 {
 		compatible = "cfi-flash";
 		reg = <0 0 0x02000000>;
 		#address-cells = <1>;
--- a/Show more
+++ b/Show more